Snow Roofing & Exteriors logo Call (817) 733-9228
Gable end & rake flashing

Gable End Flashing Replacement in Decatur, Fort Worth & DFW

Gable end flashing replacement in Decatur, Fort Worth and DFW protects the sloped edge of the roof — the rake — with drip edge and rake trim, so wind-driven rain cannot get under the shingles or behind the fascia. Snow Roofing & Exteriors replaces damaged or missing gable flashing on repairs and installs new drip edge on every shingle reroof.
  • Free inspection after hail or wind
  • Photos of everything we find
  • We meet your adjuster on the roof
  • FAA-certified drone pilot for hard-to-reach roofs
Illustration of a shingle roof meeting a brick gable wall, with edge metal turning water toward the gutter
Illustration
Why homeowners hire us for flashing work: We're a family roofing business going back 75 years. We're BBB A+ rated, fully insured, and we have 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome. References are available on request. Every visit comes with a free, itemized written estimate and a digital photo report, so you see what we see. Call (817) 733-9228 or request a free estimate.

What gable end and rake flashing are

The rake is the sloped edge of a gable roof, running from the eave up to the ridge. Gable end flashing is the metal that finishes that edge: on a shingle roof, drip edge (and sometimes a wider rake edge) that covers the deck edge and turns water away from the fascia; on a metal roof, a rake trim that caps the last panel. It is a different piece from kick-out, or return, flashing, which sits at the bottom of a roof-to-wall intersection, not along an open gable.

The International Residential Code, Section R905.2.8.5, requires drip edge at both the eaves and the rakes of asphalt-shingle roofs. At the eaves, the underlayment laps over the drip edge; at the rakes, the drip edge goes over the underlayment. Adjacent pieces are lapped at least 2 inches, the metal extends at least 1/4 inch below the sheathing and at least 2 inches onto the roof deck, and it is fastened at no more than 12 inches on center. The Asphalt Roofing Manufacturers Association describes the same eave-and-rake layout. That edge metal is what keeps wind from lifting the shingle edge and what keeps the fascia and the exposed deck edge from wicking water.

How gable end flashing fails

Missing drip edge is still common on older North Texas roofs that predate a local drip-edge requirement. Without it, water runs behind the fascia and into the rake board, and wind gets under the first course. Short, rusty, or loose drip edge, or pieces that were not lapped, leave the same path. On metal roofs, a rake trim that was never sealed at the Z-closure or that was butted instead of lapped will leak at the gable in a driving rain.

What we do on every gable end flashing job

  • On shingle reroofs we install new corrosion-resistant drip edge at every eave and every rake, lapped and fastened to the code layout above.
  • We replace rotted rake boards or fascia we find under failed edge metal, instead of covering them up.
  • On standing seam we install rake trim over a sealed Z-closure or cleat, in the same 24 or 26 gauge and color as the panels we form on our own roll formers.
  • We check the gable for a kick-out only where a lower roof or a wall actually dies into that end; an open gable does not need a diverter, it needs a tight rake edge.

We're certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. Gable-end work often goes with gutters and soffit and fascia, and we can do that as one job.

Call (817) 733-9228 or request a free estimate for gable end flashing replacement in Decatur, Fort Worth or elsewhere in DFW.

Residential warranty: a workmanship warranty from 10 years up to lifetime, depending on the job, with manufacturer warranties up to lifetime. Manufacturer coverage depends on the product and brand, and on the project qualifying for that manufacturer's program. We put the exact warranty for your roof in writing.

Certified, with 30 years installing every major roofing brand, a family roofing business going back 75 years, and over $80 million in completed roofing projects. 5.0 stars on Google at all three of our offices.

Request a free inspection or call (817) 733-9228. Small repairs are welcome too.

Frequently asked questions

What is gable end or rake flashing?

It is the metal at the sloped edge of a gable roof. On shingles that is drip edge at the rake; on standing seam it is rake trim. It keeps wind-driven rain out of the deck edge and off the fascia.

Is drip edge required at the gable?

Yes, on asphalt-shingle roofs. The International Residential Code (R905.2.8.5) requires drip edge at both eaves and rakes, with the rake drip edge installed over the underlayment and lapped and fastened to the section's minimums.

Is gable return flashing the same as rake flashing?

Not usually. People sometimes say "return flashing" when they mean a kick-out, or diverter, at the end of a roof-to-wall run. Rake flashing is the metal along an open gable edge. We install both, and they do different jobs. See our kick-out flashing page.

Do you replace drip edge when you replace a roof?

Yes. We install new drip edge at the eaves and rakes on shingle reroofs, and new rake trim on metal roofs, rather than leaving rusted or undersized edge metal under a new roof.

Get a free estimate

Tell us how to reach you. Blake or the team will call you back.

Or call (817) 733-9228 snowexteriors@gmail.com