Offices in Bridgeport · Decatur · Rhome · Class 3+ impact-rated shingles on every roof Call (817) 733-9228
Snow Roofing & Exteriors logo

Free Roof Replacement Estimate

📞 Call (817) 733-9228
Jacksboro, TX · Barn roofing

Barn Roofing in Jacksboro, TX

Snow Roofing & Exteriors roofs, repairs and builds ranch barns, hay barns, pole barns, equipment sheds and shops around Jacksboro and Jack County. We form standing seam and R-panel on our own roll formers in 24 or 26 gauge, offer corrugated and PBR panels too, and our own crew does the work. Our Bridgeport office is about 31 road miles (roughly 40 minutes) away. Call (817) 733-9228.

Working barns in Jack County ranch country

Jacksboro is the Jack County seat, at the crossroads of U.S. 281 and U.S. 380. The town grew up beside Fort Richardson, a frontier Army post built starting in 1867 that is now a state historic site just south of town. Census estimates show 4,173 residents in the 2020 base and about 4,735 in 2025. Most of the county is still ranch land, so the roofs we see out here are on hay barns, equipment sheds, pipe-framed pens, shops and ranch houses, often several on one place built decades apart.

Our Bridgeport office is about 31 road miles (roughly 40 minutes) east on U.S. 380. If you have a house and a shop or barn that both need work, we can roof them together. See roofing the house and the shop together on acreage.

Which metal goes on which building

A barn roof isn't one product. What goes on a hay barn in Jacksboro isn't always what belongs on a horse barn or a shop you can see from the back porch. Here's how we match the panel to the building:

BuildingWhat we usually recommendWhy
Hay barn, equipment barn, loafing shedR-panel or PBR, 24 or 26 gaugeStrong ribs that span open purlins, quick to install, easy to repair a panel at a time
Pole barn or post-frame buildingR-panel or PBR, with closures and trim made for the panelThe screw pattern at the eaves, rakes and ridge is what holds it down in a storm
Horse barn, stable or covered arenaR-panel, PBR or standing seam, with ventilation and condensation plannedAnimals add moisture to the air, and bare steel sweats over it
Show barn, or a barn in full view of the houseStanding seamHidden fasteners, clean lines and no exposed screws to re-tighten later
Barndominium or barn with living spaceStanding seam or R-panel over a planned insulation and vapor layerSee barndominium, shop and ag roofs
Sheds, carports, boat and RV coversCorrugated, R-panel or PBRMatches older buildings and keeps small jobs simple

We form standing seam and R-panel on our own roll formers in 24 or 26 gauge, and we also offer corrugated and PBR panels. Metal lead time is typically 1 to 2 weeks. We don't post prices, because building size, framing condition, tear-off and trim change the number a lot. You get a written price for your building.

Re-screw, re-panel or re-roof?

Most old barn roofs don't have to come off. We walk the roof where it's safe, fly a drone where it isn't, look at the purlins from inside, and show you the photos behind our call:

  • Re-screw: the panels are sound, but rubber washers have cracked in the sun or screws have backed out. New fasteners, one size up where the holes have worn oval, can add years to a roof that's otherwise fine.
  • Partial re-panel: some panels are rusted through, punctured by hail or bent by wind, usually along the eaves, the rakes or an old lean-to. We replace those panels and fix the trim and closures around them.
  • Full re-roof: rust is widespread, the old panels are too thin to hold a screw, or the barn is being enclosed or finished for living space and needs an insulation and vapor plan. See metal roof repair and restoration.

Whichever it is, we check the framing first. A new roof on rotted or undersized purlins is money spent twice.

Wind that moves barns around Jacksboro

Jack County doesn't log as much big hail as the counties east of it, but its wind reports are hard on barns. NOAA's Storm Events Database records:

  • June 1, 2019: near the Jacksboro airport, about three miles from town, emergency management reported three oak trees uprooted and a barn moved about 100 yards from its foundation near Highway 59.
  • March 18, 2020: south of Jacksboro on U.S. 281, metal storage buildings were damaged by winds from a tornadic storm.
  • December 13, 2022: reports of barns damaged along Highway 281 southeast of Jacksboro.
  • April 3, 2025: near Senate, about eight miles west, the panels and the entire truss structure of a metal outbuilding roof were blown off.
  • April 19, 2025, EF-1 tornado: near State Highway 59 and FM 1810, about eight miles northeast, it damaged the roofs of multiple outbuildings and at least three homes, with winds near 90 mph.

Hail: NOAA lists 5 reports of hail 1.75 inches (golf-ball size) or larger within about 10 miles of Jacksboro from 2016 through the September 2026 update, including 1.75-inch hail at Jacksboro and 2.75-inch hail near Jermyn on May 7, 2020, and most recently 1.75-inch hail near Stewarton on April 28, 2026. Jack County as a whole logged 17 such reports, up to 3.25 inches. Fewer people live out here to report hail, so the record likely misses storms.

What wind does to a barn roof

A house is closed on all sides. Most barns aren't. Wind blowing into an open bay or a big door pushes up on the underside of the roof while it pulls on the top, so a barn roof takes load from both sides at once. That's why the failures we see follow a pattern:

  • The edges go first. Eaves, rakes and the ridge carry the most uplift. If a panel is going to peel, it usually starts there, then the wind gets under the next one.
  • Screws loosen before they let go. Years of heat and cold work exposed fasteners loose. A loose screw leaks first, then the panel starts to lift.
  • Trim and closures matter. Missing foam closures and loose rake trim let wind and wasps in and give a gust something to grab.
  • Old lean-tos are weak links. Additions framed lighter than the main barn, or lapped onto it badly, are where many barn roofs start to fail.

When we roof or repair a barn, the fastener spacing at the edges, the trim attachment and the condition of the purlins get the most attention, because that's what keeps the roof on the building.

Jacksboro permits, and barns on county land

Inside the city limits, Jacksboro's permit fee schedule lists a roofing permit at $75 and a storage or accessory building permit at $50 (for buildings of 120 square feet or more), with building inspections at $50 each. Contractors register with the city ($50) with a license, ID and certificate of insurance on file. Every application goes in with the zoning checklist for the property. Those are city fees, not our price.

The city's accessory building rules matter for a new barn or shop in town: there has to be a main building on the lot first, shipping containers can't be used as accessory buildings, and the building has to be built of like-or-better materials than the house or similar to its neighbors. Over 500 square feet combined, it must meet the district's masonry rule or use like-or-better materials. We check that before we draw a new building.

Outside the city, Jack County Public Works says the county does not issue building permits or certificates of occupancy and has no zoning. It does permit septic systems and development in mapped flood hazard areas.

Planning several buildings on one ranch

Ranches around Jacksboro often have a house, a barn, a hay shed and a shop that all went up at different times, in different panels and colors. When one needs a roof, it's a good time to look at all of them. We walk the whole place, photograph every roof, and give you one written plan with what needs doing now, what can wait, and what it would take to make the buildings match. Because we form panels on our own roll formers, a long hay shed or equipment barn gets panels cut to the full length of each roof plane, with no laps halfway up the slope.

New barns, built by our own crews

We don't only roof barns, we build them. For a new barn, pole barn, horse barn, shop or ag building, we can bring in an architect to spec the project, or build to the specs and plans you already have. Our own crews do the work from start to finish, and the roof can go on in a color that matches the house and the other buildings so the property looks like one place.

Details that decide whether a barn roof lasts

  • Condensation control if the barn is enclosed, stores hay, houses animals or has any conditioned space. A vapor barrier or insulation under the panels and ventilation that suits the use keep it from "raining" inside. See condensation control under metal.
  • Ridge and eave closures that fit the panel profile, so wind-driven rain, birds and wasps stay out.
  • Flashing where buildings meet: lean-tos, porches, a shop wall or a stall row added later.
  • Gutters and drainage where water would otherwise sheet onto a pad, an arena entry or a doorway. See gutters.
  • Skylight panels replaced with the roof, because old clear panels turn brittle and crack long before the steel wears out.
  • Color match across the house, barn and shop.

How a barn roof job runs with us

  1. Inspection and free digital photo report: panels, fasteners, trim, purlins and framing, with measurements. You see what we see.
  2. Written options: re-screw, re-panel or re-roof, with the panel, gauge, color, trim and fastener plan spelled out.
  3. Paperwork: we check whether your barn is inside city limits or on county land, then file what applies.
  4. Panels formed for your building on our own roll formers, cut to the length of each roof plane so long runs don't need mid-slope laps.
  5. Install by our own crew, with the edges, ridge and penetrations detailed for wind.
  6. Clean-up and walk-through: a magnet sweep for screws and scrap, so nothing ends up in a hoof or a tire, and your warranty in writing.

Storm damage and insurance on barns

Hail dents and punctures panels and cracks old washers, and wind lifts edges and tears trim. Whether a barn is covered, and for how much, depends on your policy: some cover farm and ranch buildings fully, some cover them for less, and some treat cosmetic dents differently from leaks. Our photo report separates storm damage from age and rust, which is what an adjuster needs to see. If you file an insurance claim, we document the damage and meet your adjuster on the roof. Texas law requires you to pay your deductible, and a contractor may not waive, absorb or rebate it. We never will. In Texas you generally have 1 year from the date of loss to file; check your policy.

Who roofs and builds barns in Jacksboro?

Snow Roofing & Exteriors does. Here are the facts you can check before you call anyone:

  • 75 years as a family roofing business, and 30 years in the business for owner Blake Snow, who is still on the roofs.
  • Over $80 million in completed roofing projects, from small repairs to multi-million-dollar jobs.
  • 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome.
  • Our own roll formers for standing seam and R-panel, in 24 or 26 gauge, with metal lead times that are typically 1 to 2 weeks.
  • Our own crew, working about 31 road miles (roughly 40 minutes) from Jacksboro out of our Bridgeport office.
  • Snow Roofing & Exteriors is BBB A+ rated.

Photos

The barn image at the top is an illustration. The photos below are real metal roofs our crews installed on houses, shown so you can see our panel, trim and seam work up close. We don't have barn job photos from Jacksboro on file, so we don't show any. We never show a street or address.

We're certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. More nearby: barn roofing in Bridgeport, barn roofing in Chico, metal roof repair and restoration, barndominium, shop and ag roofs and our Jacksboro roofing page.

Product names, ratings and features are as published by the manufacturer and can change. We confirm the current rating and warranty of the exact product before we order it.

Residential warranty: a workmanship warranty from 10 years up to lifetime, depending on the job, with manufacturer warranties up to lifetime. Manufacturer coverage depends on the product and brand, and on the project qualifying for that manufacturer's program. We put the exact warranty for your roof in writing.

Certified, with 30 years installing every major roofing brand, a family roofing business going back 75 years, and over $80 million in completed roofing projects. 5.0 stars on Google at all three of our offices.

Request a free inspection or call (817) 733-9228. Small repairs are welcome too.

Frequently asked questions

Who roofs barns in Jacksboro, TX?

Snow Roofing & Exteriors roofs, repairs and builds ranch barns, hay barns, pole barns and shops around Jacksboro. It is a family roofing business that goes back 75 years, owner Blake Snow has 30 years in the business, the company has completed over $80 million in roofing projects, and it has 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome. Standing seam and R-panel are formed on its own roll formers in 24 or 26 gauge. The Bridgeport office is about 31 road miles (roughly 40 minutes) away. Call (817) 733-9228.

Do I need a permit to re-roof a barn in Jacksboro?

Inside the city limits, Jacksboro lists a roofing permit at $75 and a storage or accessory building permit at $50 for buildings of 120 square feet or more, and contractors must register with the city. Outside the city, Jack County does not issue building permits.

Does Jack County require a permit for a barn?

Jack County Public Works says the county does not issue building permits or certificates of occupancy and has no zoning. It does permit septic systems and development in mapped flood hazard areas.

Can I build a metal shop or barn inside Jacksboro?

Yes, with the city’s rules: there has to be a main building on the lot, shipping containers can’t be used as accessory buildings, and the building must use like-or-better materials than the house or match its neighbors. Over 500 square feet combined, it must meet the district masonry rule or use like-or-better materials.

Has wind damaged barns around Jacksboro?

Yes. NOAA notes a barn moved about 100 yards from its foundation near the Jacksboro airport on June 1, 2019, barns damaged along Highway 281 southeast of town on December 13, 2022, and a metal outbuilding roof blown off near Senate on April 3, 2025.

R-panel or PBR for my barn?

Both are exposed-fastener ribbed panels and both work on barns. PBR adds a purlin-bearing leg at the side lap for more bearing where panels overlap. We pick based on your framing, span and how the building is used.

Can you fix my old barn roof instead of replacing it?

Often, yes. If the panels are sound and only the screws and washers have failed, a re-screw can buy years. If some panels are rusted or damaged, we replace those. We recommend a full re-roof only when rust is widespread, the panels are too thin to hold a screw, or the barn is being enclosed.

Do you build new barns or only roof them?

Both. We can bring in an architect to spec a new barn, pole barn, horse barn or ag building, or build to your existing specs and plans. Our own crews do the building from start to finish.

What gauge metal do you put on a barn?

Our standing seam and R-panel roofs are 24 or 26 gauge, formed on our own roll formers. We also offer corrugated and PBR panels.

Why does my metal barn roof drip on the inside?

Usually that is condensation: warm, humid air meeting cold steel. It is fixed with a vapor barrier or insulation under the panels and ventilation that fits how the building is used.

How soon can you start a barn roof?

Metal lead time is typically 1 to 2 weeks because we form standing seam and R-panel on our own roll formers. Install time depends on the building size, tear-off and weather.

Will insurance pay for a hail-damaged barn roof?

It depends on your policy. Some policies cover farm and ranch buildings fully, some for less, and some treat cosmetic dents differently from leaks. We document the damage with photos and meet your adjuster. In Texas you generally have 1 year from the date of loss to file; check your policy.

What warranty comes with a barn roof?

Our workmanship warranty is from 10 years up to lifetime, depending on the job, plus the manufacturer’s warranty on the panel and finish, in writing.

Get a free roof inspection

We get on the roof, photograph what we find, and tell you plainly whether you need a repair or a replacement.

Free Roof Replacement Estimate

📞 Call (817) 733-9228

Certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake

Atlas Roofing certified contractor
📞 (817) 733-9228