Offices in Bridgeport · Decatur · Rhome · Class 3+ impact-rated shingles on every roof Call (817) 733-9228
Snow Roofing & Exteriors logo

Free Roof Replacement Estimate

📞 Call (817) 733-9228
Commercial roofing · Pre-bid testing

Roof Pull Tests and Core Cuts

Two small tests answer the biggest questions on a commercial re-roof: what is really under the membrane, and will new fasteners hold in the deck. A core cut shows the layers, insulation, moisture and deck. A pull test measures how much force it takes to pull a roofing fastener out of the deck. We take the core cuts ourselves. Pull and adhesion test procedures vary by manufacturer, and the manufacturer generally sends a rep to meet us on site for those tests, so the bid is built on facts.

What a core cut shows

QuestionWhat the core tells usWhy it matters
How many roofs are on there?Each membrane layer is visible in the sampleUnder the 2021 IBC reroofing rules (Section 1512), a new roof generally can't be laid over an existing roof that is water-soaked or deteriorated, or over one that already has two or more layers.
Is the insulation wet?Wet or dry, by look, feel and meterWet insulation has to come out before a coating or recover
What insulation, and how thick?Type and thickness of each layerEnergy code, tapered design and fastener length
What deck?Steel, wood, concrete, gypsum or lightweight fillFastener type, pull-test plan and attachment method
What membrane?Built-up, mod bit, single-ply or coatingCompatibility with a coating or new system

Every core is patched the same day. On older built-up roofs, samples can also go to a lab for asbestos testing when the owner or regulations require it.

How a fastener pull test works

The industry field procedure is ANSI/SPRI FX-1. In plain English:

  1. The roofing and insulation are removed down to the deck at each test spot; a core cutter is the usual tool
  2. The fastener is installed the same way it will be on the job: same fastener, same depth, same tools
  3. A calibrated gauge pulls it straight out, and the force is recorded
  4. FX-1 calls for at least 10 pulls on a roof up to 50,000 sq ft, plus 5 more for each additional 50,000 sq ft, with half of them at the corners and perimeter
  5. Each roof area with a different deck, elevation or assembly is tested separately, and every test is marked on a roof plan

Pull-test procedures vary by manufacturer, and the manufacturer generally sends a rep to meet us on site for the pull test. The manufacturer and the wind-uplift design use those numbers to set the fastener type and spacing. Low values can mean a different fastener, tighter spacing, an adhered system, or deck repairs before the new roof goes on.

Adhesion tests before a coating

Adhesion-test procedures also vary by manufacturer. A typical field test applies a small patch of coating to the cleaned roof, lets it cure, and pulls it. That shows whether the coating will bond to that surface as cleaned and primed, or whether a different primer or prep is needed. The manufacturer generally sends a rep to meet us on site for the adhesion test. See the silicone, acrylic and urethane spec guides and commercial roof coatings.

Why tests matter for warranties

Manufacturers want to know what's under their system. Pull-test results, a moisture survey and core findings are often part of the paperwork for a recover or a long-term warranty. Both 10-year and 20-year manufacturer NDL (no-dollar-limit) warranties are available on commercial jobs. The price depends on which term you choose, and the manufacturer issues an NDL warranty only after its own inspection. Read NDL vs. material vs. workmanship warranties and how a roof qualifies for a 20-year NDL.

Finding where to cut

We walk the roof, fly a drone for photos of areas that are hard to reach safely, and run drone thermal (infrared) scans that help show where water has gotten under the surface. The thermal scan tells us where to core, so a few cuts confirm what the whole roof is doing. See infrared leak detection. Every inspection comes with a free digital photo report, so you see what we see.

Ask every bidder

  • How many cores, and where? Will they be patched the same day?
  • Will fasteners be pull-tested to the manufacturer's procedure, with a manufacturer rep on site, before the attachment is chosen?
  • For a coating: has an adhesion test been done on this roof with a manufacturer rep?
  • Will the results be on a roof plan you keep?

Code sections and test standards are summarized in plain English from the published documents. Your building official, the manufacturer's current specification and the warranty document have the final word.

We're certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. We offer same-day response in almost every case, and we answer leak and storm calls 24/7 at (817) 733-9228.

Commercial warranty: a workmanship warranty from 10 years up to lifetime, depending on the job, plus both 10-year and 20-year NDL (no-dollar-limit) manufacturer warranties (the price depends on which NDL term you choose). Manufacturer coverage depends on the product and brand, and on the project qualifying for that manufacturer's program. We put the exact warranty for your roof in writing.

Certified, with 30 years installing every major roofing brand, a family roofing business going back 75 years, and over $80 million in completed roofing projects. 5.0 stars on Google at all three of our offices.

Request a free inspection or call (817) 733-9228. Small repairs are welcome too.

Frequently asked questions

What is a roof core cut?

A small sample cut through the roof down to the deck. It shows how many roofs are on the building, the insulation type and thickness, whether it is wet, and what the deck is. It is patched the same day.

What is a roof pull test?

A field test, usually to ANSI/SPRI FX-1, that measures how much force it takes to pull a roofing fastener out of the deck. Procedures vary by manufacturer, and the manufacturer generally sends a rep to meet us on site. The results set fastener type and spacing for wind uplift.

How many pull tests does a roof need?

FX-1 calls for at least 10 pulls on a roof up to 50,000 sq ft and 5 more for each additional 50,000 sq ft, with half at the corners and perimeter. The manufacturer's own procedure is the one that applies on your roof.

Who does the pull and adhesion tests?

Procedures vary by manufacturer, and the manufacturer generally sends a rep to meet us on site for the pull and adhesion tests.

Do core cuts cause leaks?

Not when they are patched properly the same day, which is part of the job.

Do I need these tests before a coating?

Yes. Cores confirm the insulation is dry, and an adhesion test confirms the coating will bond to the cleaned surface. Adhesion-test procedures vary by manufacturer, and the manufacturer generally sends a rep to meet us on site.

Which manufacturers are you certified with?

We are certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers.

Get a free roof inspection

We get on the roof, photograph what we find, and tell you plainly whether you need a repair or a replacement.

Free Roof Replacement Estimate

📞 Call (817) 733-9228

Certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake

Atlas Roofing certified contractor
📞 (817) 733-9228