Barns and shops on both sides of the county line
Azle sits on State Highway 199 about 16 miles northwest of downtown Fort Worth, and the city runs across the Tarrant–Parker county line. TSHA says the first settler, Dr. James Azle Steward, arrived in 1846 and the town grew up farming wheat, corn, peanuts and dairy cattle before housing took over. Census estimates show about 15,365 residents in 2025. Inside town, barns are mostly shops and storage buildings behind houses; west and north toward Springtown and Eagle Mountain Lake you find hay barns, horse barns and pole barns on acreage.
Our Bridgeport office is about 29 road miles (roughly 46 minutes) away. For leaks on an existing metal building, see metal roof repair: leaks at screws, seams and flashing.
Which metal goes on which building
A barn roof isn't one product. What goes on a hay barn in Azle isn't always what belongs on a horse barn or a shop you can see from the back porch. Here's how we match the panel to the building:
| Building | What we usually recommend | Why |
|---|---|---|
| Hay barn, equipment barn, loafing shed | R-panel or PBR, 24 or 26 gauge | Strong ribs that span open purlins, quick to install, easy to repair a panel at a time |
| Pole barn or post-frame building | R-panel or PBR, with closures and trim made for the panel | The screw pattern at the eaves, rakes and ridge is what holds it down in a storm |
| Horse barn, stable or covered arena | R-panel, PBR or standing seam, with ventilation and condensation planned | Animals add moisture to the air, and bare steel sweats over it |
| Show barn, or a barn in full view of the house | Standing seam | Hidden fasteners, clean lines and no exposed screws to re-tighten later |
| Barndominium or barn with living space | Standing seam or R-panel over a planned insulation and vapor layer | See barndominium, shop and ag roofs |
| Sheds, carports, boat and RV covers | Corrugated, R-panel or PBR | Matches older buildings and keeps small jobs simple |
We form standing seam and R-panel on our own roll formers in 24 or 26 gauge, and we also offer corrugated and PBR panels. Metal lead time is typically 1 to 2 weeks. We don't post prices, because building size, framing condition, tear-off and trim change the number a lot. You get a written price for your building.
Re-screw, re-panel or re-roof?
Most old barn roofs don't have to come off. We walk the roof where it's safe, fly a drone where it isn't, look at the purlins from inside, and show you the photos behind our call:
- Re-screw: the panels are sound, but rubber washers have cracked in the sun or screws have backed out. New fasteners, one size up where the holes have worn oval, can add years to a roof that's otherwise fine.
- Partial re-panel: some panels are rusted through, punctured by hail or bent by wind, usually along the eaves, the rakes or an old lean-to. We replace those panels and fix the trim and closures around them.
- Full re-roof: rust is widespread, the old panels are too thin to hold a screw, or the barn is being enclosed or finished for living space and needs an insulation and vapor plan. See metal roof repair and restoration.
Whichever it is, we check the framing first. A new roof on rotted or undersized purlins is money spent twice.
Hail and wind around Azle
NOAA's Storm Events Database lists 19 reports of hail 1.75 inches (golf-ball size) or larger within about 10 miles of Azle from 2016 through the September 2026 update. The biggest recent one was 3-inch hail at Azle on April 25, 2026, the same afternoon 2.75-inch hail fell near Westland. Others include 2-inch hail near La Junta, about three miles west, on May 3, 2021, 3-inch hail near the Saginaw airport on April 28, 2021, and 4.5-inch hail near Keeter, on the north edge of that circle, on April 1, 2024.
For barns, wind does as much damage:
- August 29, 2020: a downburst struck Briar, about seven miles north, rolling RVs and empty 18-wheelers and destroying manufactured homes and sheds.
- June 16, 2019: in Briar, thunderstorm winds pushed in the doors of a large metal garage and peeled off part of its metal roof.
- March 4, 2025 and April 25, 2026: in Springtown, about 10 miles northwest, an 85 mph wind peeled back a metal and wood roof, and an EF-1 tornado with 80 to 100 mph winds around it damaged lightweight and metal buildings.
What wind does to a barn roof
A house is closed on all sides. Most barns aren't. Wind blowing into an open bay or a big door pushes up on the underside of the roof while it pulls on the top, so a barn roof takes load from both sides at once. That's why the failures we see follow a pattern:
- The edges go first. Eaves, rakes and the ridge carry the most uplift. If a panel is going to peel, it usually starts there, then the wind gets under the next one.
- Screws loosen before they let go. Years of heat and cold work exposed fasteners loose. A loose screw leaks first, then the panel starts to lift.
- Trim and closures matter. Missing foam closures and loose rake trim let wind and wasps in and give a gust something to grab.
- Old lean-tos are weak links. Additions framed lighter than the main barn, or lapped onto it badly, are where many barn roofs start to fail.
When we roof or repair a barn, the fastener spacing at the edges, the trim attachment and the condition of the purlins get the most attention, because that's what keeps the roof on the building.
Azle permits, and barns outside the city
Azle issues permits only inside its city limits, and the city points out that an Azle mailing address or school district doesn't mean you're in the city; if you don't pay city taxes on your appraisal district bill, you're not. Inside the city, its accessory structure rules changed this year:
- Since May 4, 2026, when the city adopted the 2024 codes, every accessory building needs a permit, regardless of size. There's no fee at 120 square feet or less.
- An accessory building can cover no more than 10% of the lot, can't be taller than the house, sits behind the house at least 10 feet from it, and keeps 5-foot side and rear setbacks (15 feet on a corner lot's street side).
- A concrete foundation needs plans sealed by a Texas-registered engineer.
- On properties over five acres, an agricultural accessory building can go up without a house on the property.
The city's roofing page says a shingle replacement needs no permit, but replacing all of the decking takes a miscellaneous permit, and most miscellaneous permits run $65. For a metal re-roof on a barn in town, we ask the city at 817-444-2541 first. Outside the city, on the Parker County side, the county doesn't issue building permits; it permits septic systems and building in mapped flood zones.
Barndominiums and shops with living space
Around Azle a lot of "barns" are really shops with an office, a guest room or a full living quarters built in. Once a metal building is heated, cooled or lived in, the roof has a new job: warm, damp air inside meets cold steel and condenses, and it can drip like rain. Before we re-roof or build one, we plan the insulation and vapor layer under the panels and the ventilation for how you use the building. See condensation control under a metal roof and barndominium, shop and ag roofs.
New barns, built by our own crews
We don't only roof barns, we build them. For a new barn, pole barn, horse barn, shop or ag building, we can bring in an architect to spec the project, or build to the specs and plans you already have. Our own crews do the work from start to finish, and the roof can go on in a color that matches the house and the other buildings so the property looks like one place.
Details that decide whether a barn roof lasts
- Condensation control if the barn is enclosed, stores hay, houses animals or has any conditioned space. A vapor barrier or insulation under the panels and ventilation that suits the use keep it from "raining" inside. See condensation control under metal.
- Ridge and eave closures that fit the panel profile, so wind-driven rain, birds and wasps stay out.
- Flashing where buildings meet: lean-tos, porches, a shop wall or a stall row added later.
- Gutters and drainage where water would otherwise sheet onto a pad, an arena entry or a doorway. See gutters.
- Skylight panels replaced with the roof, because old clear panels turn brittle and crack long before the steel wears out.
- Color match across the house, barn and shop.
How a barn roof job runs with us
- Inspection and free digital photo report: panels, fasteners, trim, purlins and framing, with measurements. You see what we see.
- Written options: re-screw, re-panel or re-roof, with the panel, gauge, color, trim and fastener plan spelled out.
- Paperwork: we check whether your barn is inside city limits or on county land, then file what applies.
- Panels formed for your building on our own roll formers, cut to the length of each roof plane so long runs don't need mid-slope laps.
- Install by our own crew, with the edges, ridge and penetrations detailed for wind.
- Clean-up and walk-through: a magnet sweep for screws and scrap, so nothing ends up in a hoof or a tire, and your warranty in writing.
Storm damage and insurance on barns
Hail dents and punctures panels and cracks old washers, and wind lifts edges and tears trim. Whether a barn is covered, and for how much, depends on your policy: some cover farm and ranch buildings fully, some cover them for less, and some treat cosmetic dents differently from leaks. Our photo report separates storm damage from age and rust, which is what an adjuster needs to see. If you file an insurance claim, we document the damage and meet your adjuster on the roof. Texas law requires you to pay your deductible, and a contractor may not waive, absorb or rebate it. We never will. In Texas you generally have 1 year from the date of loss to file; check your policy.
Who roofs and builds barns in Azle?
Snow Roofing & Exteriors does. Here are the facts you can check before you call anyone:
- 75 years as a family roofing business, and 30 years in the business for owner Blake Snow, who is still on the roofs.
- Over $80 million in completed roofing projects, from small repairs to multi-million-dollar jobs.
- 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome.
- Our own roll formers for standing seam and R-panel, in 24 or 26 gauge, with metal lead times that are typically 1 to 2 weeks.
- Our own crew, working about 29 road miles (roughly 46 minutes) from Azle out of our Bridgeport office.
- Snow Roofing & Exteriors is BBB A+ rated.
Photos
The barn image at the top is an illustration. The photos below are real metal roofs our crews installed on houses, shown so you can see our panel, trim and seam work up close. We don't have barn job photos from Azle on file, so we don't show any. We never show a street or address.
We're certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. More nearby: barn roofing in Springtown, barn roofing in Rhome, barn roofing in Boyd, metal roof repair and our Azle roofing page.
Product names, ratings and features are as published by the manufacturer and can change. We confirm the current rating and warranty of the exact product before we order it.
Residential warranty: a workmanship warranty from 10 years up to lifetime, depending on the job, with manufacturer warranties up to lifetime. Manufacturer coverage depends on the product and brand, and on the project qualifying for that manufacturer's program. We put the exact warranty for your roof in writing.
Certified, with 30 years installing every major roofing brand, a family roofing business going back 75 years, and over $80 million in completed roofing projects. 5.0 stars on Google at all three of our offices.
Request a free inspection or call (817) 733-9228. Small repairs are welcome too.
