Offices in Bridgeport · Decatur · Rhome · Class 3+ impact-rated shingles on every roof Call (817) 733-9228
Snow Roofing & Exteriors logo

Free Roof Replacement Estimate

📞 Call (817) 733-9228
Denton, TX · Barn roofing

Barn Roofing in Denton, TX

Snow Roofing & Exteriors roofs, repairs and builds barns, shops, pole barns, horse barns and outbuildings in Denton and on the county land around it. We form standing seam and R-panel on our own roll formers in 24 or 26 gauge, file the City of Denton permits when your barn is inside the city, and our own crew does the work. Our Rhome office is about 22 road miles (roughly 34 minutes) away. Call (817) 733-9228.

Barns inside a city of 170,000

Denton, the Denton County seat, was founded in 1857 to be exactly that, and Census estimates show it growing from about 139,900 residents in 2020 to about 169,400 in 2025. Most people picture the Square and the two university campuses. But the city limits and the county land around them still hold a lot of acreage: horse properties and hay meadows, old farmsteads surrounded by new subdivisions, and shops, barns and barndominiums on tracts out toward Krum, Ponder, Aubrey and the lake. Some of those barns are generations old. Some went up last year.

The big difference between a barn in Denton and one a few miles out is paperwork. The City of Denton is stricter about roofs and outbuildings than most cities around it, so it matters which side of the city line your barn is on.

Which metal goes on which building

A barn roof isn't one product. What goes on a hay barn in Denton isn't always what belongs on a horse barn or a shop you can see from the back porch. Here's how we match the panel to the building:

BuildingWhat we usually recommendWhy
Hay barn, equipment barn, loafing shedR-panel or PBR, 24 or 26 gaugeStrong ribs that span open purlins, quick to install, easy to repair a panel at a time
Pole barn or post-frame buildingR-panel or PBR, with closures and trim made for the panelThe screw pattern at the eaves, rakes and ridge is what holds it down in a storm
Horse barn, stable or covered arenaR-panel, PBR or standing seam, with ventilation and condensation plannedAnimals add moisture to the air, and bare steel sweats over it
Show barn, or a barn in full view of the houseStanding seamHidden fasteners, clean lines and no exposed screws to re-tighten later
Barndominium or barn with living spaceStanding seam or R-panel over a planned insulation and vapor layerSee barndominium, shop and ag roofs
Sheds, carports, boat and RV coversCorrugated, R-panel or PBRMatches older buildings and keeps small jobs simple

We form standing seam and R-panel on our own roll formers in 24 or 26 gauge, and we also offer corrugated and PBR panels. Metal lead time is typically 1 to 2 weeks. We don't post prices, because building size, framing condition, tear-off and trim change the number a lot. You get a written price for your building.

Re-screw, re-panel or re-roof?

Most old barn roofs don't have to come off. We walk the roof where it's safe, fly a drone where it isn't, look at the purlins from inside, and show you the photos behind our call:

  • Re-screw: the panels are sound, but rubber washers have cracked in the sun or screws have backed out. New fasteners, one size up where the holes have worn oval, can add years to a roof that's otherwise fine.
  • Partial re-panel: some panels are rusted through, punctured by hail or bent by wind, usually along the eaves, the rakes or an old lean-to. We replace those panels and fix the trim and closures around them.
  • Full re-roof: rust is widespread, the old panels are too thin to hold a screw, or the barn is being enclosed or finished for living space and needs an insulation and vapor plan. See metal roof repair and restoration.

Whichever it is, we check the framing first. A new roof on rotted or undersized purlins is money spent twice.

Wind and hail around Denton

NOAA's Storm Events Database has recorded exactly the kind of damage that hits barns and metal buildings in and around Denton:

  • April 17, 2019: the Denton airport measured a 74 mph gust, and metal roofs were torn off three buildings at UNT's Rafes Urban Astronomy Center next to it. Rain through the open roofs did hundreds of thousands of dollars of damage inside.
  • May 23, 2017: thunderstorm winds severely damaged 12 to 15 small planes and about a dozen hangars at Denton Municipal Airport.
  • April 30, 2019, EF-1 tornado: it formed on the east side of the Texas Woman's University campus and ran northeast through wooded neighborhoods, mostly with 60 to 75 mph winds and spots of stronger damage.
  • May 28, 2024: Guinn Hall at TWU recorded an 83 mph gust.
  • September 19, 2023: damage to metal buildings on Southwind Place near Krum, about ten miles northwest.

NOAA lists 40 reports of hail 1.75 inches (golf-ball size) or larger within about 10 miles of Denton from 2016 through the September 2026 update. The biggest close in was April 11, 2016, with 4-inch hail in Denton under two miles from the center of the city and 2.75-inch hail near Mayhill, and 2-inch hail fell at two spots in Denton on May 24, 2020. At the edges of that circle are 4.25-inch hail near Corinth (March 26, 2017) and the 5.9-inch hail near Sanger (June 15, 2023).

What wind does to a barn roof

A house is closed on all sides. Most barns aren't. Wind blowing into an open bay or a big door pushes up on the underside of the roof while it pulls on the top, so a barn roof takes load from both sides at once. That's why the failures we see follow a pattern:

  • The edges go first. Eaves, rakes and the ridge carry the most uplift. If a panel is going to peel, it usually starts there, then the wind gets under the next one.
  • Screws loosen before they let go. Years of heat and cold work exposed fasteners loose. A loose screw leaks first, then the panel starts to lift.
  • Trim and closures matter. Missing foam closures and loose rake trim let wind and wasps in and give a gust something to grab.
  • Old lean-tos are weak links. Additions framed lighter than the main barn, or lapped onto it badly, are where many barn roofs start to fail.

When we roof or repair a barn, the fastener spacing at the edges, the trim attachment and the condition of the purlins get the most attention, because that's what keeps the roof on the building.

City of Denton rules for barns, shops and outbuildings

Inside the city, two pages on the City of Denton's site decide most barn projects:

  • Accessory structures need a building permit. The city's accessory structures page says sheds, detached garages, carports, shops and similar outbuildings typically require one. The only exemption is a one-story storage building of 200 square feet or less with no power, water or air conditioning, and even that still has to meet zoning.
  • They have to fit the house. The same page says accessory structures shall be architecturally compatible with the main structure, can't sit in the front or side yard, and the plans have to show that compatibility.
  • Plans for a new building. A new barn or shop needs a site plan, floor, foundation, framing and roof plans and elevations, filed through the city's eTRAKiT portal.
  • Roofs are permitted work too. Denton's roofing page has required a permit for all residential roof and re-roof projects since June 1, 2022, issued before tear-off and pulled only by contractors registered with the city as general contractors. If the roofing material is changing, the city does a plan review first, and replaced decking needs its own alteration permit. For a barn roof in the city, we confirm with Development Services at (940) 349-8600 which of these applies and file it.

Outside the city limits, Denton County's Development Services department requires a Development Permit for any new building or structure in unincorporated areas, plus a culvert permit for a new drive off a county road. We check your tract before we draw anything.

Matching the barn to the house in Denton

Because the city wants accessory structures to be architecturally compatible with the house, the roof is often the easiest place to tie a new barn or shop to the home. A standing seam or painted R-panel roof in the same color as a metal house roof, or a color picked to go with the house's shingles and brick, plus matching trim and a similar roof pitch where the design allows, gives the plans reviewer something clear to look at. We put the panel profile, color chip and trim details into the drawings so the review isn't held up by a question about looks.

New barns, built by our own crews

We don't only roof barns, we build them. For a new barn, pole barn, horse barn, shop or ag building, we can bring in an architect to spec the project, or build to the specs and plans you already have. Our own crews do the work from start to finish, and the roof can go on in a color that matches the house and the other buildings so the property looks like one place.

Details that decide whether a barn roof lasts

  • Condensation control if the barn is enclosed, stores hay, houses animals or has any conditioned space. A vapor barrier or insulation under the panels and ventilation that suits the use keep it from "raining" inside. See condensation control under metal.
  • Ridge and eave closures that fit the panel profile, so wind-driven rain, birds and wasps stay out.
  • Flashing where buildings meet: lean-tos, porches, a shop wall or a stall row added later.
  • Gutters and drainage where water would otherwise sheet onto a pad, an arena entry or a doorway. See gutters.
  • Skylight panels replaced with the roof, because old clear panels turn brittle and crack long before the steel wears out.
  • Color match across the house, barn and shop.

How a barn roof job runs with us

  1. Inspection and free digital photo report: panels, fasteners, trim, purlins and framing, with measurements. You see what we see.
  2. Written options: re-screw, re-panel or re-roof, with the panel, gauge, color, trim and fastener plan spelled out.
  3. Paperwork: we check whether your barn is inside city limits or on county land, then file what applies.
  4. Panels formed for your building on our own roll formers, cut to the length of each roof plane so long runs don't need mid-slope laps.
  5. Install by our own crew, with the edges, ridge and penetrations detailed for wind.
  6. Clean-up and walk-through: a magnet sweep for screws and scrap, so nothing ends up in a hoof or a tire, and your warranty in writing.

Storm damage and insurance on barns

Hail dents and punctures panels and cracks old washers, and wind lifts edges and tears trim. Whether a barn is covered, and for how much, depends on your policy: some cover farm and ranch buildings fully, some cover them for less, and some treat cosmetic dents differently from leaks. Our photo report separates storm damage from age and rust, which is what an adjuster needs to see. If you file an insurance claim, we document the damage and meet your adjuster on the roof. Texas law requires you to pay your deductible, and a contractor may not waive, absorb or rebate it. We never will. In Texas you generally have 1 year from the date of loss to file; check your policy.

Who roofs and builds barns in Denton?

Snow Roofing & Exteriors does. Here are the facts you can check before you call anyone:

  • 75 years as a family roofing business, and 30 years in the business for owner Blake Snow, who is still on the roofs.
  • Over $80 million in completed roofing projects, from small repairs to multi-million-dollar jobs.
  • 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome.
  • Our own roll formers for standing seam and R-panel, in 24 or 26 gauge, with metal lead times that are typically 1 to 2 weeks.
  • Our own crew, working about 22 road miles (roughly 34 minutes) from Denton out of our Rhome office.
  • Snow Roofing & Exteriors is BBB A+ rated.

Photos

The barn image at the top is an illustration. The photos below are real metal roofs our crews installed on houses, shown so you can see our panel, trim and seam work up close. We don't have barn job photos from Denton on file, so we don't show any. We never show a street or address.

We're certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. More in Denton: metal roofing in Denton, standing seam in Denton, commercial roofing in Denton, storm damage in Denton, siding in Denton and our Denton roofing page. Nearby: barn roofing in Krum, barn roofing in Argyle and barn roofing in Sanger.

Product names, ratings and features are as published by the manufacturer and can change. We confirm the current rating and warranty of the exact product before we order it.

Residential warranty: a workmanship warranty from 10 years up to lifetime, depending on the job, with manufacturer warranties up to lifetime. Manufacturer coverage depends on the product and brand, and on the project qualifying for that manufacturer's program. We put the exact warranty for your roof in writing.

Certified, with 30 years installing every major roofing brand, a family roofing business going back 75 years, and over $80 million in completed roofing projects. 5.0 stars on Google at all three of our offices.

Request a free inspection or call (817) 733-9228. Small repairs are welcome too.

Frequently asked questions

Who roofs barns in Denton?

Snow Roofing & Exteriors roofs, repairs and builds barns, shops, pole barns, horse barns and outbuildings in Denton and on the county land around it. It is a family roofing business that goes back 75 years, owner Blake Snow has 30 years in the business, the company has completed over $80 million in roofing projects, and it has 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome. Standing seam and R-panel are formed on its own roll formers in 24 or 26 gauge. The Rhome office is about 22 road miles (roughly 34 minutes) away. Call (817) 733-9228.

Do I need a permit for a barn or shop in Denton?

Inside the city, usually yes. Denton says accessory structures like sheds, garages, carports and shops typically need a building permit, and the only exemption is a one-story storage building of 200 square feet or less with no power, water or air conditioning. On county land, Denton County requires a Development Permit for new buildings.

Does my barn have to match my house in Denton?

Inside the city, the accessory structures page says they shall be architecturally compatible with the main structure, and the plans have to show it. A roof color and profile that ties to the house is often the simplest way to get there.

Do I need a permit to re-roof a barn in Denton?

Denton requires a permit for all residential roof and re-roof projects, pulled before tear-off by a contractor registered with the city, and a plan review if the roofing material changes. For a barn or outbuilding we confirm with Development Services which permit applies and file it.

Has wind torn metal roofs off in Denton?

Yes. On April 17, 2019, NOAA lists metal roofs torn off three buildings at UNT’s Rafes Urban Astronomy Center when the Denton airport measured a 74 mph gust, and on May 23, 2017 about a dozen hangars at Denton Municipal Airport were damaged by thunderstorm winds.

My barn is outside the city limits. What applies?

On unincorporated land, Denton County requires a Development Permit for any new building or structure and a culvert permit for a new drive off a county road. For a re-roof on an existing barn, we confirm with the county whether anything is needed before we start.

R-panel or PBR for my barn?

Both are exposed-fastener ribbed panels and both work on barns. PBR adds a purlin-bearing leg at the side lap for more bearing where panels overlap. We pick based on your framing, span and how the building is used.

Can you fix my old barn roof instead of replacing it?

Often, yes. If the panels are sound and only the screws and washers have failed, a re-screw can buy years. If some panels are rusted or damaged, we replace those. We recommend a full re-roof only when rust is widespread, the panels are too thin to hold a screw, or the barn is being enclosed.

Do you build new barns or only roof them?

Both. We can bring in an architect to spec a new barn, pole barn, horse barn or ag building, or build to your existing specs and plans. Our own crews do the building from start to finish.

What gauge metal do you put on a barn?

Our standing seam and R-panel roofs are 24 or 26 gauge, formed on our own roll formers. We also offer corrugated and PBR panels.

Why does my metal barn roof drip on the inside?

Usually that is condensation: warm, humid air meeting cold steel. It is fixed with a vapor barrier or insulation under the panels and ventilation that fits how the building is used.

How soon can you start a barn roof?

Metal lead time is typically 1 to 2 weeks because we form standing seam and R-panel on our own roll formers. Install time depends on the building size, tear-off and weather.

What warranty comes with a barn roof?

Our workmanship warranty is from 10 years up to lifetime, depending on the job, plus the manufacturer’s warranty on the panel and finish, in writing.

Get a free roof inspection

We get on the roof, photograph what we find, and tell you plainly whether you need a repair or a replacement.

Free Roof Replacement Estimate

📞 Call (817) 733-9228

Certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake

Atlas Roofing certified contractor
📞 (817) 733-9228