Horse barns and estate barns in Argyle
Argyle is on U.S. 377 about six miles southwest of Denton. Peters Colony families settled the area in the 1850s, when it was known as Pilot Knob or Waintown, and Census estimates show it growing from 4,399 residents in 2020 to about 6,372 in 2025. Much of it is acreage and estate lots, with newer HOA neighborhoods in between, and a lot of property carries an Argyle address without being inside the town limits.
Barns in Argyle tend to be seen as much as used. A horse barn, a covered arena or a hay barn on an Argyle estate usually sits in full view of the house and the drive, so it has to look right as well as stay dry. That's why standing seam makes sense on more barns here than in most places we work, and why color match between the house, the barn and the shop gets real attention. Argyle's zoning also sets its own standards for keeping horses and other animals on residential lots, including minimum acreage and distances from streets, lot lines and neighbors, so for a new stable we confirm those with the town before the design is final.
Which metal goes on which building
A barn roof isn't one product. What goes on a hay barn in Argyle isn't always what belongs on a horse barn or a shop you can see from the back porch. Here's how we match the panel to the building:
| Building | What we usually recommend | Why |
|---|---|---|
| Hay barn, equipment barn, loafing shed | R-panel or PBR, 24 or 26 gauge | Strong ribs that span open purlins, quick to install, easy to repair a panel at a time |
| Pole barn or post-frame building | R-panel or PBR, with closures and trim made for the panel | The screw pattern at the eaves, rakes and ridge is what holds it down in a storm |
| Horse barn, stable or covered arena | R-panel, PBR or standing seam, with ventilation and condensation planned | Animals add moisture to the air, and bare steel sweats over it |
| Show barn, or a barn in full view of the house | Standing seam | Hidden fasteners, clean lines and no exposed screws to re-tighten later |
| Barndominium or barn with living space | Standing seam or R-panel over a planned insulation and vapor layer | See barndominium, shop and ag roofs |
| Sheds, carports, boat and RV covers | Corrugated, R-panel or PBR | Matches older buildings and keeps small jobs simple |
We form standing seam and R-panel on our own roll formers in 24 or 26 gauge, and we also offer corrugated and PBR panels. Metal lead time is typically 1 to 2 weeks. We don't post prices, because building size, framing condition, tear-off and trim change the number a lot. You get a written price for your building.
Standing seam on a barn: when it's worth it
R-panel is the workhorse for barns, and on a hay barn behind the tree line it's usually the right answer. Standing seam costs more but earns it on a barn that's part of the view. The fasteners are hidden under the seam, so there are no rows of screws and washers to age in the sun and re-tighten later. The lines are cleaner, the panel can match the house exactly, and long runs go eave to ridge in one piece from our roll formers. On an Argyle estate where the barn sits beside the drive, a common plan is standing seam on the house and the front barn and R-panel on the working buildings further back, all in one color.
Re-screw, re-panel or re-roof?
Most old barn roofs don't have to come off. We walk the roof where it's safe, fly a drone where it isn't, look at the purlins from inside, and show you the photos behind our call:
- Re-screw: the panels are sound, but rubber washers have cracked in the sun or screws have backed out. New fasteners, one size up where the holes have worn oval, can add years to a roof that's otherwise fine.
- Partial re-panel: some panels are rusted through, punctured by hail or bent by wind, usually along the eaves, the rakes or an old lean-to. We replace those panels and fix the trim and closures around them.
- Full re-roof: rust is widespread, the old panels are too thin to hold a screw, or the barn is being enclosed or finished for living space and needs an insulation and vapor plan. See metal roof repair and restoration.
Whichever it is, we check the framing first. A new roof on rotted or undersized purlins is money spent twice.
Wind and hail around Argyle
Argyle sits in one of the busiest hail areas we serve. NOAA's Storm Events Database lists 62 reports of hail 1.75 inches (golf-ball size) or larger within about 10 miles of Argyle from 2016 through the September 2026 update. Close to town:
- June 11, 2023: 3.5-inch hail near Bartonville, about a mile and a half away, 3-inch hail near Smoots, and 4.25-inch hail near Bartonville about five miles away.
- March 26, 2017: 2.75-inch hail in Argyle, about a mile from the center of town, and 4.25-inch hail near Corinth.
- March 14, 2024: 2.5-inch hail in Argyle and 3.5-inch hail near Bartonville.
- April 1, 2024: 3-inch hail near Smoots, under three miles west, and 3.4-inch hail near Justin.
Wind matters as much on open acreage. On May 28, 2024, a member of the public measured an 86 mph gust west of Double Oak, about four miles east of Argyle. On March 2, 2023, trees came down across Argyle roads and power poles were snapped. NOAA also lists wind damage to a barn southwest of Ponder in March 2018 and about a dozen hangars damaged at the Denton airport in May 2017, both within about nine miles. On a barn, hail punches holes and cracks skylight panels, and wind works the eaves and rakes. Our photo report covers every building on the property, not just the house.
What wind does to a barn roof
A house is closed on all sides. Most barns aren't. Wind blowing into an open bay or a big door pushes up on the underside of the roof while it pulls on the top, so a barn roof takes load from both sides at once. That's why the failures we see follow a pattern:
- The edges go first. Eaves, rakes and the ridge carry the most uplift. If a panel is going to peel, it usually starts there, then the wind gets under the next one.
- Screws loosen before they let go. Years of heat and cold work exposed fasteners loose. A loose screw leaks first, then the panel starts to lift.
- Trim and closures matter. Missing foam closures and loose rake trim let wind and wasps in and give a gust something to grab.
- Old lean-tos are weak links. Additions framed lighter than the main barn, or lapped onto it badly, are where many barn roofs start to fail.
When we roof or repair a barn, the fastener spacing at the edges, the trim attachment and the condition of the purlins get the most attention, because that's what keeps the roof on the building.
Town of Argyle rules for barns and accessory buildings
The Town of Argyle's permits page says permits are required before the new construction, addition, alteration or repair of existing buildings and structures, and every contractor registers with the town each year ($125 the first year, $50 to renew). For barns and outbuildings, the town's residential accessory buildings handout adds:
- A permit for almost every accessory building. The only exception is a portable building no larger than 120 square feet and no taller than 8.5 feet.
- Agricultural use is allowed. Accessory buildings in residential districts can't be living space, rented or used for business, but the handout makes an exception for agricultural use.
- Height. In single-family districts, accessory buildings top out at 20 feet unless a specific use permit is approved for a building that uses the same materials and design as the house. Plan a tall hay barn or arena with that in mind.
- A house comes first. Accessory buildings have to be on the same lot as the residence and aren't allowed without a main structure.
- Setbacks. Side and rear setbacks of at least 10 feet, with the building at least 10 feet from the house.
We call Permits at (940) 464-7273 to confirm the scope for a re-roof and file what the town requires. Land with an Argyle address outside the town limits falls under Denton County, which requires a Development Permit for any new building or structure in unincorporated areas.
New barns, built by our own crews
We don't only roof barns, we build them. For a new barn, pole barn, horse barn, shop or ag building, we can bring in an architect to spec the project, or build to the specs and plans you already have. Our own crews do the work from start to finish, and the roof can go on in a color that matches the house and the other buildings so the property looks like one place.
Details that decide whether a barn roof lasts
- Condensation control if the barn is enclosed, stores hay, houses animals or has any conditioned space. A vapor barrier or insulation under the panels and ventilation that suits the use keep it from "raining" inside. See condensation control under metal.
- Ridge and eave closures that fit the panel profile, so wind-driven rain, birds and wasps stay out.
- Flashing where buildings meet: lean-tos, porches, a shop wall or a stall row added later.
- Gutters and drainage where water would otherwise sheet onto a pad, an arena entry or a doorway. See gutters.
- Skylight panels replaced with the roof, because old clear panels turn brittle and crack long before the steel wears out.
- Color match across the house, barn and shop.
How a barn roof job runs with us
- Inspection and free digital photo report: panels, fasteners, trim, purlins and framing, with measurements. You see what we see.
- Written options: re-screw, re-panel or re-roof, with the panel, gauge, color, trim and fastener plan spelled out.
- Paperwork: we check whether your barn is inside city limits or on county land, then file what applies.
- Panels formed for your building on our own roll formers, cut to the length of each roof plane so long runs don't need mid-slope laps.
- Install by our own crew, with the edges, ridge and penetrations detailed for wind.
- Clean-up and walk-through: a magnet sweep for screws and scrap, so nothing ends up in a hoof or a tire, and your warranty in writing.
Storm damage and insurance on barns
Hail dents and punctures panels and cracks old washers, and wind lifts edges and tears trim. Whether a barn is covered, and for how much, depends on your policy: some cover farm and ranch buildings fully, some cover them for less, and some treat cosmetic dents differently from leaks. Our photo report separates storm damage from age and rust, which is what an adjuster needs to see. If you file an insurance claim, we document the damage and meet your adjuster on the roof. Texas law requires you to pay your deductible, and a contractor may not waive, absorb or rebate it. We never will. In Texas you generally have 1 year from the date of loss to file; check your policy.
Who roofs and builds barns in Argyle?
Snow Roofing & Exteriors does. Here are the facts you can check before you call anyone:
- 75 years as a family roofing business, and 30 years in the business for owner Blake Snow, who is still on the roofs.
- Over $80 million in completed roofing projects, from small repairs to multi-million-dollar jobs.
- 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome.
- Our own roll formers for standing seam and R-panel, in 24 or 26 gauge, with metal lead times that are typically 1 to 2 weeks.
- Our own crew, working about 15 road miles (roughly 27 minutes) from Argyle out of our Rhome office.
- Snow Roofing & Exteriors is BBB A+ rated.
Photos
The barn image at the top is an illustration. The photos below are real metal roofs our crews installed on houses, shown so you can see our panel, trim and seam work up close. We don't have barn job photos from Argyle on file, so we don't show any. We never show a street or address.
We're certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. More in Argyle: metal roofing in Argyle, standing seam in Argyle, storm damage in Argyle, slate roofing in Argyle, metal roofs and hail in Argyle, covered outdoor kitchens and pavilions and our Argyle roofing page. Nearby: barn roofing in Justin, barn roofing in Denton and metal roofs for horse barns and arenas.
Product names, ratings and features are as published by the manufacturer and can change. We confirm the current rating and warranty of the exact product before we order it.
Residential warranty: a workmanship warranty from 10 years up to lifetime, depending on the job, with manufacturer warranties up to lifetime. Manufacturer coverage depends on the product and brand, and on the project qualifying for that manufacturer's program. We put the exact warranty for your roof in writing.
Certified, with 30 years installing every major roofing brand, a family roofing business going back 75 years, and over $80 million in completed roofing projects. 5.0 stars on Google at all three of our offices.
Request a free inspection or call (817) 733-9228. Small repairs are welcome too.
