Metal roofs in Sunset, TX make a lot of sense. Out here in southern Montague County most properties are a house, a shop and a barn or two on open ground, and a good metal roof handles the hail and wind on all of them for decades.
I’m Blake Snow. I’ve been roofing for 30 years, I’m the third generation in a family business that goes back 75 years, and our crews have completed over $80 million in roofing projects. Our Bridgeport office is about 23 road miles from Sunset, roughly a 34-minute drive, and we form our own standing seam and R-panel on our own roll formers. Here’s how I’d plan a metal roof on a Sunset property.
The short version
- House: standing seam is the long-term pick. Hidden fasteners, clean lines, fewer leak points.
- Shop and barn: R-panel or PBR does the job well and costs less.
- Gauge: every metal roof we install is 24 or 26 gauge steel.
- Hail is real here. NOAA has 2.5-inch hail on record at Sunset.
- Wind is the everyday test. Open land means edges, eaves and ridges need to be fastened right.
- Lead time: typically 1 to 2 weeks for metal.
Metal roofs in Sunset, TX: what’s different out here
Sunset is a small, unincorporated town on a spur of State Highway 101, at the west end of Farm Road 1749, a short drive off U.S. 287. It’s ranch and farm country. That changes how I think about a roof in three ways:
- There’s usually more than one building. The house, the shop, the hay barn and maybe a carport or a covered porch. Planning them together saves money and makes the property look like one place.
- There’s nothing to block the wind. On open pasture, gusts hit a roof straight on. Wind gets under the eaves and rakes and pulls up on the edges. That’s where metal roofs fail first when they’re not tied down well.
- Hail comes through here. More on that below, with the NOAA records.
Standing seam or R-panel on the house?
Both are metal, both shed hail and rain, and both outlast an ordinary shingle roof. The difference is the fasteners.
| Standing seam | R-panel / PBR | |
|---|---|---|
| Fasteners | Hidden under the seam | Exposed screws through the panel |
| Upkeep | Very little | Screws and washers checked over the years |
| Look | Clean vertical lines, finished look | Ribbed, ranch and ag look |
| Best fit | Houses, porches, high-end shops | Shops, barns, simple houses on a budget |
| Cost | Higher | Lower |
On a house you plan to live in for a long time, I’d lean standing seam. The screws on an exposed-fastener roof are fine when they’re new, but the rubber washers age in the Texas sun and the screws can loosen as the metal expands and contracts. That’s the most common metal roof leak we fix. With standing seam the fasteners sit under the seam, out of the weather. If you want the details, read hidden fasteners vs. exposed screws.
R-panel is still a good roof. On a simple ranch house where budget matters most, a well-installed 26 gauge R-panel roof on solid framing will serve you a long time. We never talk anyone out of the roof that fits their budget.
If you like the look of shingles or shake but want steel, stone-coated steel and metal shingles are another option.
Matching the house, the shop and the barn
This is where Sunset properties are different from a subdivision. Folks often ask us to do the whole place at once, or at least to plan it so it matches later. A few ways to do it:
- Same color everywhere. Charcoal, dark bronze, barn red, galvalume, or whatever goes with your stone and trim. See metal roof colors and finishes.
- Standing seam on the house, R-panel on the shop in the same color. The property looks matched without paying standing seam prices on a 60-foot shop.
- Long panels, one piece. Because we roll form on our own machines, panels can run from ridge to eave in one piece on most buildings. Fewer laps means fewer places for water and wind to get in. More on that in roofing the house and shop together.
If your shop or barn is a separate project, our barn roofing in Sunset page and the Montague County ag building guide cover re-screwing, re-paneling and condensation in more detail.
Hail near Sunset: what the records show
I only quote storm records I can point to. NOAA’s Storm Events Database lists:
- 2.5-inch hail at Sunset on April 11, 2016, along with a 1.75-inch report the same day.
- Baseball-size hail along Highway 287 between Alvord and Sunset in that same April 2016 storm.
- 2-inch hail at Sunset on April 17, 2019.
- 25 reports of golf-ball-size or larger hail in Montague County from 2016 through mid-2026.
What does that mean for a metal roof? Hail that size can dent metal panels, but it rarely punches through 24 or 26 gauge steel the way it can crack shingles and break the mat. A dented metal roof usually still keeps water out. Whether dents count as damage on your claim depends on your policy, so read the wording or ask your agent before you buy. Metal roofs and hail goes into this.
If a storm already came through, we’ll do a free storm and hail inspection with a digital photo report. In Texas you generally have 1 year from the date of loss to file a claim, but check your policy.
Wind: fastening a metal roof on open land
On a Sunset property, wind does more day-to-day work on a roof than hail does. Here’s what we do so the roof stays put:
- Fasten into solid framing. Every screw or clip lands in the decking, purlin or batten it’s meant for. If the framing is rotted or loose, we tell you before we put new steel on top.
- More fasteners at the edges. Eaves, rakes, ridges and corners see the strongest uplift, so they get fastened to the panel maker’s schedule.
- Closed edges. Eave trim, rake trim, closures and ridge cap keep wind from getting under the panels.
- Good underlayment on houses. Under standing seam on a house we use a synthetic or high-temperature underlayment, so the roof stays dry if a panel ever does get damaged.
Shingles to metal: what the switch looks like
Many older houses around Sunset have shingle roofs that are on their second or third round of hail. Switching to metal is a common project for us. We tear off the old shingles, check and repair the decking, put down new underlayment, flash the chimney, vents and walls, and install the panels and trim. Our step-by-step shingles to standing seam guide walks through it.
Gauge, lead time and warranty
- Gauge: 24 or 26 gauge steel on every metal roof we install. Here’s what the gauge number means.
- Lead time: our metal lead time is typically 1 to 2 weeks.
- Workmanship warranty: from 10 years up to lifetime, depending on the job, plus the manufacturer’s coverage on the materials.
We’re certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. We’re fully insured, BBB A+ rated, and we have 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome. References are available on request.
Questions to ask any metal roofer in Montague County
Whoever you hire, ask these before you sign:
- What gauge is the metal, and who makes the panels?
- Is it standing seam with hidden fasteners or exposed-fastener panel?
- Will the panels run ridge to eave in one piece?
- How are the eaves, rakes and ridges fastened for wind?
- What underlayment goes under it on the house?
- What’s the workmanship warranty, in writing?
- How soon can the metal be on site?
Sunset and southern Montague County
We work in Sunset and across southern Montague County, including Bowie, Forestburg, Montague and Nocona, plus nearby Alvord and Chico in Wise County. Whether it’s the house, the shop or the whole place, we’ll come look, measure and send you a free digital photo report.
Let’s look at your roof
Call (817) 733-9228 or use the free estimate form below. Tell us what buildings you’re thinking about, and we’ll put together a plan for metal roofs on your Sunset property.

