Snow Roofing & Exteriors logo Call (817) 733-9228
Termination bar · Commercial flashing

Termination Bar Installation in Decatur, Fort Worth & DFW

Termination bar installation in Decatur, Fort Worth and DFW is how we finish a commercial wall flashing: an aluminum bar that clamps the membrane to the wall, with sealant in compression and, when the wall allows it, counter flashing over the top. Snow Roofing & Exteriors installs these details to the membrane manufacturer's instructions on TPO, EPDM, PVC and modified-bitumen roofs.
  • TPO, PVC, modified bitumen, metal and coatings
  • Repairs, restorations and new roofs
  • 10- and 20-year NDL warranties available
  • American WeatherStar Approved Contractor
Illustration of metal flashing against a masonry wall, the kind of joint a termination bar and counter flashing protect
Illustration
Why homeowners hire us for flashing work: We're a family roofing business going back 75 years. We're BBB A+ rated, fully insured, and we have 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome. References are available on request. Every visit comes with a free, itemized written estimate and a digital photo report, so you see what we see. Call (817) 733-9228 or request a free estimate.

What a termination bar is and where it goes

A termination bar is a narrow extruded aluminum bar, typically about an inch wide, that is fastened through the flashing membrane into a solid wall. Manufacturers such as Carlisle and Johns Manville use it for compression-type terminations: a bead of water cut-off mastic sits between the membrane and the wall, the bar is fastened so that mastic stays in compression, and a compatible sealant is tooled along the top edge of the bar. It is used at the top of a wall flashing, at parapets, at intermediate wall heights, and sometimes at other membrane edges. Johns Manville's TPO wall details show the bar fastened about 12 inches on center, with a small gap between bar sections, and they call for a minimum flashing height of 8 inches above the roof surface on those details.

The bar by itself is only half of a durable detail. The same manufacturers publish details that cover the bar with surface-mounted or cut-in counter flashing, so rain running down the wall never sits on the sealant line. On some Johns Manville details, a termination bar alone is associated with a shorter maximum guarantee term than the same termination covered by counter flashing. We install the detail the manufacturer specifies for the system and warranty you choose.

How a termination bar fails

The usual failures are loose or missing fasteners, a sealant bead that was never tooled or has dried out, no mastic under compression behind the bar, bars butted tight with no gap, or a bar left uncovered on a wall that sheds a lot of water. Once the compression is gone, water gets behind the membrane and shows up as a leak at the wall, often far from the fastener that failed.

What we do on every termination bar job

  • We use the membrane manufacturer's termination bar, fasteners, water cut-off mastic and sealant, installed so the mastic stays in compression.
  • We tool a sealant bead along the top edge of the bar and leave the small gap between bar sections the details call for.
  • Where the wall allows it, we cover the bar with counter flashing, cut into masonry when we can, so the sealant line is not the only defense.
  • We inspect and photograph existing bars on leak calls, and we replace rather than recaulk when the bar, the fasteners or the membrane behind it are no longer sound.

We're certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. On commercial jobs we can also offer 10- and 20-year NDL manufacturer warranties when the project qualifies.

For termination bar installation or repair in Decatur, Fort Worth or elsewhere in DFW, call (817) 733-9228 or request a free estimate.

Commercial warranty: a workmanship warranty from 10 years up to lifetime, depending on the job, plus both 10-year and 20-year NDL (no-dollar-limit) manufacturer warranties (the price depends on which NDL term you choose). Manufacturer coverage depends on the product and brand, and on the project qualifying for that manufacturer's program. We put the exact warranty for your roof in writing.

Certified, with 30 years installing every major roofing brand, a family roofing business going back 75 years, and over $80 million in completed roofing projects. 5.0 stars on Google at all three of our offices.

Request a free inspection or call (817) 733-9228. Small repairs are welcome too.

Frequently asked questions

What is a termination bar on a roof?

A termination bar is an aluminum bar fastened through a commercial roof membrane at a wall or parapet. It keeps a bead of mastic in compression and is sealed along the top. It is how TPO, EPDM and similar flashings are clamped to the wall.

Does a termination bar need counter flashing?

It should whenever the wall allows it. Manufacturer details often cover the bar with surface-mounted or cut-in counter flashing so water running down the wall does not sit on the sealant. Some warranties are shorter when the bar is left uncovered.

Do you install termination bars on TPO and EPDM roofs?

Yes. We install termination bars and wall flashings on TPO, EPDM, PVC and modified-bitumen roofs, using the membrane manufacturer's bar, mastic and sealant. See also our <a href="/commercial-roofing">commercial roofing</a> and <a href="/tpo-roofing">TPO</a> pages.

Can you recaulk a leaking termination bar?

Sometimes a failed top bead is all that is wrong, and a clean, compatible reseal will do. If fasteners are loose, the mastic has lost compression, or the membrane behind the bar is split, we replace the detail instead of caulking over it.

Get a free estimate

Tell us how to reach you. Blake or the team will call you back.

Or call (817) 733-9228 snowexteriors@gmail.com