Snow Roofing & Exteriors logo Call (817) 733-9228
Carrollton, TX · Metal roofing

Metal Roofing in Carrollton, TX

Metal roofing in Carrollton, TX is mostly a question of what to put on a 1970s or 1980s home that's on its third or fourth roof. Snow Roofing & Exteriors installs every kind of metal roof here: standing seam, stone-coated steel and metal shingles for HOA streets, copper accents, and R-panel or PBR for garages, shops and outbuildings, all in 24 or 26 gauge with standing seam and R-panel formed on our own roll formers. Our Rhome-area team is about 36 road miles (roughly 56 minutes) away. Call (817) 733-9228.
  • Hidden screws and clean, straight lines
  • Formed on our own roll formers, right on the job
  • 24 or 26 gauge steel in many colors
  • Workmanship warranty from 10 years up to lifetime, depending on the job
Illustration of a modern farmhouse with a bronze standing seam metal roof

A city built mostly in one decade

Carrollton sits on Interstate 35E about 14 miles north of downtown Dallas, in parts of Dallas, Denton and Collin counties. William and Mary Larner settled here in 1842, the A. W. Perry family followed two years later at Trinity Mills, and the town grew up as a rail and shipping point after the Cotton Belt crossed the Katy here in 1888. Then the Dallas boom hit: Carrollton went from about 13,900 people in 1970 to about 40,600 in 1980, and according to the Handbook of Texas almost three-quarters of the city's year-round homes at that point had been built during that one decade. Census estimates show about 134,500 residents today.

That history is why metal comes up so often here. When most of a city's homes go up in the same ten years, they reach the same milestones together: same-age decking, same builder ventilation, similar pitches, and roofs that have been replaced after hail two or three times already. Owners who are tired of the cycle start asking which metal fits the house:

PropertyWhat we usually recommend
1970s-80s brick ranch or two-storyStone-coated steel or metal shingles that read as shingle from the curb, or a full standing seam roof in a dark finish
Newer home with an HOA in north CarrolltonStone-coated steel or metal shingle in an approved color; standing seam on porches, bays and entries
Home on an open lot or near the Elm Fork greenbeltStanding seam with clip spacing tightened at the eaves, rakes and ridge
Modern remodel or farmhouse-style additionA full standing seam roof, usually charcoal, black or dark bronze
Detached garage, shop, carport or RV coverR-panel, PBR or corrugated, or standing seam to match the house

Every kind of metal roof, not just one

Most "metal roofing" searches in Carrollton start with standing seam, but it isn't the only right answer. Here's what we install and where each one fits:

Metal systemWhat it looks likeWhere it fits best
Standing seamFlat pans with raised seams, fasteners hiddenFull roofs on modern, farmhouse and transitional homes; porch and bay accents
Stone-coated steelSteel with a stone granule finish shaped like shake, tile or shingleOwners who want metal's strength but a traditional look a neighborhood is used to
Metal shingles and metal tilePressed steel panels in shingle, slate or tile profilesHomes where the street view has to read as shingle, slate or tile
Copper accentsBright copper that weathers to brown, then greenBay windows, entry roofs, dormers and cupolas on traditional homes
R-panel, PBR and corrugatedRibbed panels with exposed screws and washersShops, barns, garages, pool cabanas, boat and RV covers

We don't quote prices on the web because pitch, size, tear-off and detail work move them too much. We'll give you a written number for each option that makes sense on your roof.

Older decking and low sections: what we check first

Many of Carrollton's boom-era homes have a low-slope back porch or wing, and many are on decking that has been nailed through two or three times. Both matter for metal. On a low-slope porch, wing or back section we use mechanically seamed standing seam rather than a snap-lock panel, because the seam is folded closed along its length, and we check the manufacturer's minimum slope for the exact panel. On the main roof, we check every sheet of decking after tear-off and re-nail or replace what won't hold a clip or screw. Metal is only as well attached as the wood under it.

Carrollton's wind record

NOAA's event narratives show why we pay as much attention to edges and fasteners here as to hail:

  • March 13, 2019: a measured gust of about 75 mph and wind damage across mostly the southern part of Carrollton, from Valley Ranch toward Addison Airport.
  • March 21, 2022: a brief EF-0 tornado in northern Carrollton near Old Denton Road and Rosemeade Parkway lifted a section of an apartment building's roof and stripped a large section of shingles nearby.
  • June 2, 2022: wind peeled metal roofing pieces off several residences at an RV park in Carrollton.
  • May 28, 2024: a spotter reported a roof torn from a commercial building at Keller Springs and Midway, with winds estimated at 80 mph in Valley Ranch just south.
  • March 4, 2025: an amateur radio operator measured an 82 mph gust about a mile southeast of Hebron Parkway and Josey Lane.

Those reports, especially the metal roofing peeled off homes in June 2022, are a good lesson: metal fails at its edges and fasteners, not in the middle of the panel. On a Carrollton roof we use:

  • Tighter clip and fastener spacing at the perimeter (eaves, rakes, hips and ridge), where uplift is highest, following the manufacturer's tested pattern.
  • Trim made for the panel, hemmed and cleated, instead of face-screwed loose trim that wind can catch.
  • Deck and nailing checked after tear-off, because a metal roof is only as well attached as the wood under it.
  • Closures sized to the panel at the ridge and eaves so wind-driven rain stays out.

Hail around Carrollton

NOAA's Storm Events Database lists 29 reports of hail 1.75 inches (golf-ball size) or larger within about 10 miles of Carrollton from 2016 through the September 2026 update. The biggest ones close to town:

  • June 6, 2018: 3-inch hail in Carrollton, about two and a half miles from the center of the city, with 1.75-inch hail less than a mile from the center and 2.75-inch hail near Hebron. The same storm dropped 2.75- to 3-inch hail in Coppell.
  • June 11, 2023: 3-inch hail about seven miles north near the lake, with 2.5-inch hail near Lewisville about six miles away.
  • April 20, 2023: 3-inch hail in Plano, and 1-inch hail in Carrollton the same day.
  • September 25, 2024: 2-inch hail about five miles east in west Plano.
  • May 23, 2026: 1.5-inch hail about a mile from the center of the city near Trinity Mills, and June 2, 2026: 2-inch hail about nine miles north.

Metal isn't hail-proof. Very large hail can dent steel, and some policies treat cosmetic dents differently from leaks, so read the policy before you choose. A 24- or 26-gauge panel won't crack, curl or shed granules the way shingles do. See Class 4 metal roofs and insurance. Texas insurers must offer a premium credit for UL 2218 impact-rated roofs, but each company sets its own amount, and Class 4 earns the largest. We can't promise a discount; ask your insurer for their figure in writing. After a qualifying install we fill out TDI Form PC068 for you. If you file an insurance claim, we document the damage and meet your adjuster on the roof. Texas law requires you to pay your deductible, and a contractor may not waive, absorb or rebate it. We never will. In Texas you generally have 1 year from the date of loss to file; check your policy.

Carrollton's roof permit rule is different

Most cities around Carrollton want a permit for every re-roof. Carrollton doesn't. The City's re-roofing page says a roofing permit is required only when structural members that support the roof are replaced, such as the roof deck or sheathing. Replacing the roofing system itself (shingles, shakes, tiles, metal panels, underlayment, membranes, cover boards and insulation) does not need a permit. What that means for you:

  • The code still applies. The City's building inspection FAQ is plain about it: even when no permit is required, the adopted code has to be followed. We install to code and to the manufacturer's specs either way.
  • Decking changes the picture. If tear-off shows soft or rotten decking, replacing it is structural work, and that part needs a permit, applied for through the City's CityServe portal, with an inspection when the work is done. The City allows replacement decking of the same thickness as the existing deck, however much is replaced.
  • Registration comes first. Per the City's contractor registration page, permits aren't issued until every contractor on the job is registered, registration renews every year, and it's free.
  • Patio covers are different. The City lists patio covers, awnings and canopies among the residential projects that need a permit.

Because we often don't know how much decking is bad until the old roof is off, we tell you up front what we'll do if we find it, put the decking line in writing, and handle the permit and inspection if it's needed. Questions about a specific address go to Carrollton Building Inspection at 972-466-3225.

For a metal roof, that rule means the permit usually turns on the deck, not the panels. We still tear off to the deck on every metal job instead of going over old shingles, so we can fix the decking, correct the ventilation and lay high-temperature underlayment made for metal.

Getting metal past an HOA in Carrollton

Many neighborhoods in Carrollton have an HOA, and committees mostly care about how the roof reads from the street and whether the color fits the neighborhood. Stone-coated steel and metal shingles read as shake, shingle or tile from the curb; standing seam is often approved first on porches, bays and entries. We put together the product sheet, color chip, profile drawing and impact rating so the committee can decide on the first pass. Approval is always up to your HOA.

Garages, shops and RV covers

Plenty of Carrollton lots have a detached garage, workshop or covered RV or boat parking behind the house. We re-panel and re-roof them in R-panel, PBR or standing seam, color-matched to the house. Our crews also handle siding, gutters and windows, so one crew can finish the whole exterior. The City lists patio covers and accessory structures over 120 square feet among projects that need a permit; we confirm it with Building Inspection before we build one.

Why it matters that we form our own panels

  • One piece from eave to ridge. We cut standing seam and R-panel to the length of each roof plane, so long runs don't need mid-slope laps.
  • 24 or 26 gauge on every standing seam and R-panel roof. See 26 vs. 29 gauge.
  • No waiting in a panel shop's queue after a hailstorm, when everyone needs a roof at once. Metal lead time is typically 1 to 2 weeks.
  • Flashings bent for the panel, not caulked: walls, chimneys, valleys, skylights and pipes.
  • Every inspection comes with a free digital photo report, so you see what we see.

How a metal roof job runs with us

  1. Inspection and free digital photo report: deck, ventilation, penetrations, valleys and measurements.
  2. Written spec for each option: system, gauge, profile, color, underlayment, trim and every flashing detail.
  3. Approvals: the HOA or historic-review packet if you need one, then the permit.
  4. Tear-off and deck repair where needed, then high-temperature synthetic underlayment made for metal.
  5. Install by our own crew, with hips, ridges, eaves and penetrations detailed for the system.
  6. Final walk-through, a magnet sweep of the yard and driveway, and your warranty in writing.

Who installs metal roofs in Carrollton?

Snow Roofing & Exteriors does. Here are the facts you can check before you call anyone:

  • 75 years as a family roofing business, and 30 years in the business for owner Blake Snow, who is still on the roofs.
  • Over $80 million in completed roofing projects, from small repairs to multi-million-dollar jobs.
  • 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome.
  • Our own roll formers for standing seam and R-panel, in 24 or 26 gauge, with metal lead times that are typically 1 to 2 weeks.
  • Our own crew, about 36 road miles (roughly 56 minutes) from Carrollton with our Rhome-area team.
  • Snow Roofing & Exteriors is BBB A+ rated.

Our metal work, up close

The photos on this page show our roof work up close. We never show a street or address.

We're certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. We give a workmanship warranty from 10 years up to lifetime, depending on the job, and the manufacturer warranty on the panel and finish, in writing.

More in Carrollton: metal roofing in Carrollton, standing seam in Carrollton and our Carrollton roofing page. Nearby: metal roofing in Coppell, Lewisville, The Colony and Plano.

Product names, ratings and features are as published by the manufacturer and can change. We confirm the current rating and warranty of the exact product before we order it.

Residential warranty: a workmanship warranty from 10 years up to lifetime, depending on the job, with manufacturer warranties up to lifetime. Manufacturer coverage depends on the product and brand, and on the project qualifying for that manufacturer's program. We put the exact warranty for your roof in writing.

Certified, with 30 years installing every major roofing brand, a family roofing business going back 75 years, and over $80 million in completed roofing projects. 5.0 stars on Google at all three of our offices.

Request a free inspection or call (817) 733-9228. Small repairs are welcome too.

Charcoal standing seam metal roof on a brick ranch home near Rhome, TX
Charcoal standing seam on a brick ranch
Dark bronze standing seam metal roof replacing shingles on a red brick ranch home near Sanger, TX
Dark standing seam replacing shingles on a brick ranch
Standing seam metal roof on a blue board-and-batten wing of a ranch estate
Standing seam on a board-and-batten wing
Close-up of a gray standing seam metal roof with matching painted vent stacks and pipe flashings
Gray standing seam with painted vent stacks and pipe flashings
Side elevation of a brick home with multiple hips in standing seam metal
Multiple hips in standing seam
Detail of a shake-to-standing-seam metal transition
Where a shake roof meets standing seam
Close view of standing seam panels at the eave of a brick ranch home
Seams running straight to the eave
Snow Roofing crew at the panel trailer beside a brick garage during a standing seam install
Our crew and panel trailer on install day

Frequently asked questions

Who installs metal roofs in Carrollton?

Snow Roofing & Exteriors installs standing seam, stone-coated steel, metal shingle, copper accent, R-panel and PBR roofs on homes, garages, shops and RV covers in Carrollton. It is a family roofing business that goes back 75 years, owner Blake Snow has 30 years in the business, the company has completed over $80 million in roofing projects, it is BBB A+ rated, and it has 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome. Standing seam and R-panel are formed on its own roll formers in 24 or 26 gauge. Its Rhome-area team is about 36 road miles (roughly 56 minutes) away. Call (817) 733-9228.

Do I need a permit for a metal roof in Carrollton?

Usually not for the panels themselves. Carrollton's re-roofing page says a roofing permit is required only when structural members such as the roof deck or sheathing are replaced; replacing shingles, metal panels and underlayment does not need one. If we replace decking, that work needs a permit, and the code applies either way.

What happens if you find bad decking on my Carrollton roof?

We show you photos, replace it, and pull the City permit that structural decking work requires, with an inspection when it's done. Carrollton allows replacement decking of the same thickness as the existing deck. We put the decking terms in writing before we start.

Can a metal roof go over my shingles?

We don't do it on metal jobs. Tearing off to the deck lets us fix soft decking, correct ventilation and lay high-temperature underlayment made for metal, which is what the panel and its warranty depend on.

Has Carrollton had big hail?

Yes. NOAA lists 29 reports of hail 1.75 inches or larger within about 10 miles from 2016 through September 2026, including 3-inch hail in Carrollton on June 6, 2018, about two and a half miles from the center of the city.

Will a metal roof hold up to Carrollton wind?

When the edges are done right, yes. NOAA lists an 82 mph gust measured near Hebron Parkway and Josey Lane on March 4, 2025. We tighten clip and fastener spacing at the eaves, rakes and ridge to the manufacturer's tested pattern and use trim made for the panel.

Will my HOA allow a metal roof?

Many allow stone-coated steel or metal shingles that read as shingle from the street, and many approve standing seam accents. We prepare the product sheet, color chip and profile drawing. Approval is up to your HOA.

Is standing seam the only metal option?

No. We also install stone-coated steel and metal shingles or tile for a traditional look, copper accents, and R-panel, PBR or corrugated on shops, barns and covers.

What gauge metal do you install?

24 or 26 gauge steel on every standing seam and R-panel roof. We don’t install 29 gauge on homes.

How soon can a metal roof start?

Metal lead time is typically 1 to 2 weeks, because we form standing seam and R-panel on our own roll formers. HOA approval and the permit can add time, so we start that paperwork right after you sign.

What warranty do you give on a metal roof?

A workmanship warranty from 10 years up to lifetime, depending on the job, plus the manufacturer warranty on the panel and finish, in writing.

Get a free estimate

Tell us how to reach you. Blake or the team will call you back.

Or call (817) 733-9228 snowexteriors@gmail.com