Where standing seam fits in Carrollton
Carrollton sits on Interstate 35E about 14 miles north of downtown Dallas, in parts of Dallas, Denton and Collin counties. William and Mary Larner settled here in 1842, the A. W. Perry family followed two years later at Trinity Mills, and the town grew up as a rail and shipping point after the Cotton Belt crossed the Katy here in 1888. Then the Dallas boom hit: Carrollton went from about 13,900 people in 1970 to about 40,600 in 1980, and according to the Handbook of Texas almost three-quarters of the city's year-round homes at that point had been built during that one decade. Census estimates show about 134,500 residents today.
Standing seam shows up on Carrollton homes in a few ways:
- Full roofs on boom-era brick homes that have had their shingles replaced after hail more than once. A dark standing seam roof over red or tan brick is the conversion we're asked about most.
- Low-slope back sections and porches, where a mechanically seamed panel handles the low pitch better than shingles do.
- Accents over porches, bays and entries with a designer or Class 4 shingle main roof, the usual answer where an HOA limits full metal.
- Patio covers and porch roofs over outdoor living space (a permitted project in Carrollton).
Comparing standing seam with stone-coated steel or metal shingles? See metal roofing in Carrollton.
Snap-lock or mechanically seamed?
| Snap-lock | Mechanically seamed | |
|---|---|---|
| How the seam closes | Panels snap together by hand | A seaming tool folds the seam closed along its length |
| Best on | Most steep-slope house roofs | Low-slope porches and wings, and very long runs |
| Look from the street | Clean, slim seam | Slightly heavier seam; same concealed fasteners |
More detail: snap-lock vs. mechanical lock. We use 24 or 26 gauge steel and never 29 gauge on a home (why). We don't publish prices because size, pitch, tear-off and detail work move them too much; our standing seam cost page explains what moves the number, and you get a written price for your roof.
Low pitch is where standing seam earns its keep
Shingles need enough slope to shed water; on flatter porch and wing sections they wear fast and leak at the laps. Standing seam doesn't have laps in the field. Every panel runs eave to ridge in one piece, and on low porches and wings we use mechanically seamed panels so the seam is folded closed along its full length. We check the manufacturer's minimum slope for the exact panel and seam before we quote it, and if a section is too flat for any steep-slope roof, we'll tell you and quote the right low-slope system for it.
Built for Carrollton's wind
NOAA lists an 82 mph gust measured near Hebron Parkway and Josey Lane on March 4, 2025, a brief EF-0 tornado in northern Carrollton in March 2022 that stripped shingles nearby, and metal roofing peeled off homes at an RV park in June 2022. Standing seam handles that kind of wind well when it's installed to the manufacturer's tested system. What we do on every Carrollton roof:
- Clip spacing tightened at the perimeter. Uplift is highest at the eaves, rakes, hips and ridge, so that's where the clips go closer together, per the manufacturer's pattern.
- Hemmed panel ends and cleated trim, so there's no raw edge or loose flange for wind to get under.
- Mechanically seamed panels on low-pitch sections and where the exposure calls for the extra seam strength.
- Deck nailing checked after tear-off, because the clips can only hold as well as the wood they're screwed into.
Color, finish and the street view
On Carrollton's brick homes, charcoal, black and dark bronze are the colors we're asked about most; lighter grays and tans blend with stone and run cooler in summer. We bring real panel samples, put the exact color and finish system in writing, and include the profile drawing and product sheet in your HOA packet if you have one. See metal roof colors and finishes. Approval is up to your HOA.
What a good standing seam job looks like up close
- One panel from eave to ridge, formed to the length of each roof plane.
- Clips that let the panels move with the heat, so they don't oil-can or pull fasteners.
- Bent flashings, not caulk, at walls, chimneys, valleys, skylights and pipes.
- High-temperature underlayment made for metal, over a deck we've checked and repaired.
- Vent piping and flues reconnected and flashed, and any decking we replace documented for the City permit that structural work needs.
Carrollton's roof permit rule is different
Most cities around Carrollton want a permit for every re-roof. Carrollton doesn't. The City's re-roofing page says a roofing permit is required only when structural members that support the roof are replaced, such as the roof deck or sheathing. Replacing the roofing system itself (shingles, shakes, tiles, metal panels, underlayment, membranes, cover boards and insulation) does not need a permit. What that means for you:
- The code still applies. The City's building inspection FAQ is plain about it: even when no permit is required, the adopted code has to be followed. We install to code and to the manufacturer's specs either way.
- Decking changes the picture. If tear-off shows soft or rotten decking, replacing it is structural work, and that part needs a permit, applied for through the City's CityServe portal, with an inspection when the work is done. The City allows replacement decking of the same thickness as the existing deck, however much is replaced.
- Registration comes first. Per the City's contractor registration page, permits aren't issued until every contractor on the job is registered, registration renews every year, and it's free.
- Patio covers are different. The City lists patio covers, awnings and canopies among the residential projects that need a permit.
Because we often don't know how much decking is bad until the old roof is off, we tell you up front what we'll do if we find it, put the decking line in writing, and handle the permit and inspection if it's needed. Questions about a specific address go to Carrollton Building Inspection at 972-466-3225.
Hail and standing seam in Carrollton
NOAA's Storm Events Database lists 29 reports of hail 1.75 inches (golf-ball size) or larger within about 10 miles of Carrollton from 2016 through the September 2026 update. The biggest ones close to town:
- June 6, 2018: 3-inch hail in Carrollton, about two and a half miles from the center of the city, with 1.75-inch hail less than a mile from the center and 2.75-inch hail near Hebron. The same storm dropped 2.75- to 3-inch hail in Coppell.
- June 11, 2023: 3-inch hail about seven miles north near the lake, with 2.5-inch hail near Lewisville about six miles away.
- April 20, 2023: 3-inch hail in Plano, and 1-inch hail in Carrollton the same day.
- September 25, 2024: 2-inch hail about five miles east in west Plano.
- May 23, 2026: 1.5-inch hail about a mile from the center of the city near Trinity Mills, and June 2, 2026: 2-inch hail about nine miles north.
No roof is hail-proof, and very large hail can dent steel. Standing seam doesn't crack, curl or lose granules, so it usually keeps shedding water after storms that ruin shingles. If you'd rather keep a shingle look on the main roof, we'll compare Class 4 designer shingles with full metal. See Class 4 metal roofs and insurance. Texas insurers must offer a premium credit for UL 2218 impact-rated roofs, but each company sets its own amount, and Class 4 earns the largest. We can't promise a discount; ask your insurer for their figure in writing. After a qualifying install we fill out TDI Form PC068 for you. If you file an insurance claim, we document the damage and meet your adjuster on the roof. Texas law requires you to pay your deductible, and a contractor may not waive, absorb or rebate it. We never will. In Texas you generally have 1 year from the date of loss to file; check your policy.
Why it matters that we form our own panels
- One piece from eave to ridge. We cut standing seam and R-panel to the length of each roof plane, so long runs don't need mid-slope laps.
- 24 or 26 gauge on every standing seam and R-panel roof. See 26 vs. 29 gauge.
- No waiting in a panel shop's queue after a hailstorm, when everyone needs a roof at once. Metal lead time is typically 1 to 2 weeks.
- Flashings bent for the panel, not caulked: walls, chimneys, valleys, skylights and pipes.
- Every inspection comes with a free digital photo report, so you see what we see.
How a metal roof job runs with us
- Inspection and free digital photo report: deck, ventilation, penetrations, valleys and measurements.
- Written spec for each option: system, gauge, profile, color, underlayment, trim and every flashing detail.
- Approvals: the HOA or historic-review packet if you need one, then the permit.
- Tear-off and deck repair where needed, then high-temperature synthetic underlayment made for metal.
- Install by our own crew, with hips, ridges, eaves and penetrations detailed for the system.
- Final walk-through, a magnet sweep of the yard and driveway, and your warranty in writing.
Who installs standing seam roofs in Carrollton?
Snow Roofing & Exteriors does. Here are the facts you can check before you call anyone:
- 75 years as a family roofing business, and 30 years in the business for owner Blake Snow, who is still on the roofs.
- Over $80 million in completed roofing projects, from small repairs to multi-million-dollar jobs.
- 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome.
- Our own roll formers for standing seam and R-panel, in 24 or 26 gauge, with metal lead times that are typically 1 to 2 weeks.
- Our own crew, about 36 road miles (roughly 56 minutes) from Carrollton with our Rhome-area team.
- Snow Roofing & Exteriors is BBB A+ rated.
Our metal work, up close
The photos on this page show our roof work up close. We never show a street or address.
We're certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. We give a workmanship warranty from 10 years up to lifetime, depending on the job, and the manufacturer warranty on the panel and finish, in writing.
More: metal roofing in Carrollton, our Carrollton roofing page, and nearby standing seam in Coppell, Lewisville, The Colony and Plano.
Product names, ratings and features are as published by the manufacturer and can change. We confirm the current rating and warranty of the exact product before we order it.
Residential warranty: a workmanship warranty from 10 years up to lifetime, depending on the job, with manufacturer warranties up to lifetime. Manufacturer coverage depends on the product and brand, and on the project qualifying for that manufacturer's program. We put the exact warranty for your roof in writing.
Certified, with 30 years installing every major roofing brand, a family roofing business going back 75 years, and over $80 million in completed roofing projects. 5.0 stars on Google at all three of our offices.
Request a free inspection or call (817) 733-9228. Small repairs are welcome too.








