Metal roofing for a Dallas commercial roof: where it fits
Dallas has every kind of commercial building: older warehouses and industrial buildings along the freeway and rail corridors, metal shops and flex space on the edges of the city, churches with steep sanctuaries and flat wings, and strip centers with mansards over flat roofs. Metal isn’t the answer for every roof plane, but where it fits it usually outlasts the alternatives. This is how we start:
| Building | What we usually recommend | Why |
|---|---|---|
| Pre-engineered metal building, warehouse or flex space | PBR or R-panel, 24 or 26 gauge | Fast to install on purlins and economical; full-length panels avoid end laps |
| Low-slope metal building with recurring leaks | Mechanically seamed standing seam | Seams sit above the water line, and clips let long panels move with the heat |
| Office, restaurant, dealership or retail with a roof you can see | Snap-lock or mechanically seamed standing seam | Hidden fasteners, clean lines and a color that matches the storefront |
| Mansard or canopy on a flat-roof building | Standing seam formed to length on site | Replaces tired shingle or wood mansards with a cleaner, longer-lasting face |
| Old screw-down roof on a sound frame | Retrofit over the existing roof or a metal roof coating | No tear-off over inventory, tenants or production |
| Flat section behind a parapet | TPO, PVC or modified bitumen, tied into the metal | Not every roof plane should be metal |
We price each option that genuinely fits the building and tell you why we'd pick one. We don't publish prices because size, slope, tear-off, insulation and access move them too much.
When metal beats another flat roof
A lot of Dallas owners call us after the second or third membrane on a building that was never quite flat enough to drain. If the structure allows it, a metal retrofit builds a light sub-frame over the existing roof, creates real slope, and puts standing seam on top, with no tear-off over the space below. Where a retrofit isn't right, we say so and quote a TPO or PVC roof instead.
Repair, retrofit, coat or replace?
Most metal buildings we're called to have the same short list of problems: screw washers dried out by the sun, rust starting at end laps, hail-cracked light panels, trim bent by wind and leaks around rooftop units. The fix depends on what the panels and frame look like up close:
- Repair: new fasteners, one size up where holes are worn, resealed laps, new closures and trim, when the panels are sound.
- Coat: a metal roof coating over sound panels after the fasteners and laps are fixed.
- Retrofit: new sub-framing and new panels over the old roof. It can turn a leaky low slope into a better-draining one and leaves room for insulation, with no tear-off.
- Tear off and replace: when rust is through the panels, the insulation is wet or the frame needs work.
Every inspection comes with a free digital photo report, so you see what we see. We inspect every section, fly a drone over areas that aren't safe to walk, and mark everything on a roof plan so every bidder is pricing the same roof.
Code basics that decide the design
- Slope: the 2021 International Building Code sets minimum slopes for metal panels: 3:12 for lapped, non-soldered panels without lap sealant, 1/2:12 with applied lap sealant, and 1/4:12 for standing seam. A roof flatter than its panel allows is the most common source of chronic leaks we see on metal buildings.
- Recovering: a new roof generally can't go over a water-soaked or deteriorated roof, or over two or more existing layers, so we check for moisture before recommending a recover or retrofit.
- Condensation: on an enclosed building, insulation, a vapor retarder and ventilation are planned with the roof. Many "leaks" in metal buildings are condensation on cool mornings.
City of Dallas permits for a commercial roof
Dallas issues a dedicated Commercial Roofing Permit. The city's permitting and inspections directory lists three inspections for it: a Roofing Final, an Energy Code inspection and a Zoning Final. (A residential roofing permit carries only the roofing and zoning finals.) Dallas exempts re-roofing that doesn't exceed the equivalent of two roofing squares, so nearly every commercial job needs the permit.
- The energy code is part of the job. When a commercial roof is torn off and replaced, the insulation question comes with it, and Dallas checks it with its own inspection. We plan insulation thickness at edges, curbs and doors from the first walk.
- Questions go to the right desk. Dallas Building Inspection lists [email protected] for commercial roof repair code questions; we use it when a scope needs a ruling.
- Zoning final. Rooftop screening, parapet height and equipment placement can come up at the zoning final, so we note them in the scope.
We file the permit, schedule each inspection and give you the closeout packet with the city finals and warranty paperwork.
Hail and wind on Dallas commercial roofs
NOAA's Storm Events Database lists 12 reports of hail 1.75 inches (golf-ball size) or larger within about 10 miles of Dallas (measured from the city center) from 2016 through the September 2026 update. The largest was 2.5-inch hail near New Hope on June 2, 2017, and 2-inch hail was reported near Elam and Balch Springs on June 12, 2023. NOAA also lists 4 tornado reports within that radius, the strongest an EF2 on October 20, 2019. Dallas covers far more than 10 miles, so its north and west sides share the busier hail record of Irving, Carrollton and the Mid-Cities.
Large hail can dent metal panels, crack light panels and damage rooftop units. Dents alone may be cosmetic, and coverage depends on your policy, so read any cosmetic-damage exclusion now. After a storm we document every section with photos and a roof plan and can meet your adjuster on the roof. If you file an insurance claim, we document the damage and meet your adjuster on the roof. Texas law requires you to pay your deductible, and a contractor may not waive, absorb or rebate it. We never will. In Texas you generally have 1 year from the date of loss to file; check your policy.
Keeping the building open
- Phased work, section by section, so nothing is left open overnight and tenants or production keep running.
- Trucks, lifts and material drops scheduled around your hours, docks and parking.
- Certificates of insurance before we start, and one point of contact from bid to closeout.
- Warranties in writing: our workmanship warranty from 10 years up to lifetime, depending on the job, panel and paint warranties from the manufacturer, and 10- or 20-year NDL (no-dollar-limit) manufacturer warranties on the commercial systems that offer them.
Who installs commercial metal roofs in Dallas?
Snow Roofing & Exteriors does. Here are the facts you can check:
- Owner Blake Snow brings 30 years of large commercial and industrial roofing, including the Imperial Palace casino in Biloxi in 2006, right after Hurricane Katrina, and full exterior and interior rehabs on national-brand hotel properties around the DFW Metroplex.
- Over $80 million in completed roofing projects, from small repairs to multi-million-dollar jobs, in a family roofing business that goes back 75 years.
- Our own roll formers for standing seam and R-panel in 24 or 26 gauge, with metal lead times that are typically 1 to 2 weeks.
- 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome. Snow Roofing & Exteriors is BBB A+ rated, fully insured, with references available on request.
Bidder checklist for a Dallas commercial metal roof
- Panel profile, gauge (24 or 26) and paint system, in writing
- One-piece panels or end laps, and how any laps are sealed
- Clip and fastener type and spacing per the manufacturer
- Insulation, vapor control, closures and trim
- Gutters, light panels, curbs and rooftop units included or excluded
- Who pulls the Dallas permit and calls for inspections
- Workmanship, panel, finish and any NDL warranty terms
What our photos show
The pictures on this page show our commercial membrane and standing seam work up close. We'll walk you through photos of buildings like yours when we meet.
We're certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. Statewide guide: commercial metal roofing. More for Dallas owners: warehouse roofing in Dallas, church roofing in Dallas, strip mall roofing in Dallas, commercial metal roofing in Irving and our Dallas roofing page.
Product names, ratings and features are as published by the manufacturer and can change. We confirm the current rating and warranty of the exact product before we order it.
Commercial warranty: a workmanship warranty from 10 years up to lifetime, depending on the job, plus both 10-year and 20-year NDL (no-dollar-limit) manufacturer warranties (the price depends on which NDL term you choose). Manufacturer coverage depends on the product and brand, and on the project qualifying for that manufacturer's program. We put the exact warranty for your roof in writing.
Certified, with 30 years installing every major roofing brand, a family roofing business going back 75 years, and over $80 million in completed roofing projects. 5.0 stars on Google at all three of our offices.
Request a free inspection or call (817) 733-9228. Small repairs are welcome too.






