Commercial metal roofing in Irving, TX: which roof fits which building
Irving has one of the biggest commercial and industrial bases in the Metroplex, between DFW Airport, State Highways 183 and 114, and Las Colinas. That means pre-engineered warehouses and distribution buildings near the airport, older metal shops and flex buildings in the original parts of town, and offices, hotels and retail with mansards and canopies that people see every day. This is how we usually start:
| Building | What we usually recommend | Why |
|---|---|---|
| Pre-engineered metal building, warehouse or flex space | PBR or R-panel, 24 or 26 gauge | Fast to install on purlins and economical; full-length panels avoid end laps |
| Low-slope metal building with recurring leaks | Mechanically seamed standing seam | Seams sit above the water line, and clips let long panels move with the heat |
| Office, restaurant, dealership or retail with a roof you can see | Snap-lock or mechanically seamed standing seam | Hidden fasteners, clean lines and a color that matches the storefront |
| Mansard or canopy on a flat-roof building | Standing seam formed to length on site | Replaces tired shingle or wood mansards with a cleaner, longer-lasting face |
| Old screw-down roof on a sound frame | Retrofit over the existing roof or a metal roof coating | No tear-off over inventory, tenants or production |
| Flat section behind a parapet | TPO, PVC or modified bitumen, tied into the metal | Not every roof plane should be metal |
We price each option that genuinely fits the building and tell you why we'd pick one. We don't publish prices because size, slope, tear-off, insulation and access move them too much.
Repair, retrofit, coat or replace?
Most metal buildings we're called to have the same short list of problems: screw washers dried out by the sun, rust starting at end laps, hail-cracked light panels, trim bent by wind and leaks around rooftop units. The fix depends on what the panels and frame look like up close:
- Repair: new fasteners, one size up where holes are worn, resealed laps, new closures and trim, when the panels are sound.
- Coat: a metal roof coating over sound panels after the fasteners and laps are fixed.
- Retrofit: new sub-framing and new panels over the old roof. It can turn a leaky low slope into a better-draining one and leaves room for insulation, with no tear-off.
- Tear off and replace: when rust is through the panels, the insulation is wet or the frame needs work.
Every inspection comes with a free digital photo report, so you see what we see. We inspect every section, fly a drone over areas that aren't safe to walk, and mark everything on a roof plan so every bidder is pricing the same roof.
Code basics that decide the design
- Slope: the 2021 International Building Code sets minimum slopes for metal panels: 3:12 for lapped, non-soldered panels without lap sealant, 1/2:12 with applied lap sealant, and 1/4:12 for standing seam. A roof flatter than its panel allows is the most common source of chronic leaks we see on metal buildings.
- Recovering: a new roof generally can't go over a water-soaked or deteriorated roof, or over two or more existing layers, so we check for moisture before recommending a recover or retrofit.
- Condensation: on an enclosed building, insulation, a vapor retarder and ventilation are planned with the roof. Many "leaks" in metal buildings are condensation on cool mornings.
City of Irving permits for a commercial metal re-roof
Irving's permit pages say building permits are required to erect, enlarge, alter, move, demolish or repair a structure, and the city's fee schedule lists re-roofing and roofing overlays per structure or building, at $150 for commercial (and $150 for multifamily). Applications, contractor registration and inspection requests go through the city's MGO portal. The city's Building Inspections FAQ tells owners to check that a contractor is registered with Irving and insured, and not to pull a permit on a contractor's behalf. We register, file in our name, and send the certificate of insurance to the owner and property manager before work starts.
Scopes that go beyond a like-for-like re-roof, such as a retrofit with new sub-framing, raised curbs or added insulation, can bring plan review, structural or energy-code questions. We confirm the permit path with Irving Inspections ([email protected]) before we schedule, so there are no surprises mid-job.
Hail and wind on Irving commercial roofs
NOAA's Storm Events Database lists 15 reports of hail 1.75 inches (golf-ball size) or larger within about 10 miles of Irving from 2016 through the September 2026 update. The largest was 3-inch hail near Coppell on June 6, 2018, about 7 miles from Irving, and on May 27, 2024 hail up to 2.75 inches was reported near Bedford and Euless, just west across the county line. NOAA also lists 9 tornado reports within about 10 miles, the strongest an EF3 on October 20, 2019.
Metal handles hail better than most commercial roofs, but large hail can dent panels, crack light panels and damage trim and rooftop unit fins. Dents alone may be cosmetic, and whether that's covered depends on your policy, so read any cosmetic-damage exclusion before you need it. After a storm we document every section with photos and a roof plan, and we can meet your adjuster on the roof. We don't adjust or negotiate claims. If you file an insurance claim, we document the damage and meet your adjuster on the roof. Texas law requires you to pay your deductible, and a contractor may not waive, absorb or rebate it. We never will. In Texas you generally have 1 year from the date of loss to file; check your policy.
Keeping the building open
- Phased work, section by section, so nothing is left open overnight and tenants or production keep running.
- Trucks, lifts and material drops scheduled around your hours, docks and parking.
- Certificates of insurance before we start, and one point of contact from bid to closeout.
- Warranties in writing: our workmanship warranty from 10 years up to lifetime, depending on the job, panel and paint warranties from the manufacturer, and 10- or 20-year NDL (no-dollar-limit) manufacturer warranties on the commercial systems that offer them.
Near DFW Airport and the distribution corridors, that often means working around truck courts and dock schedules; at Las Colinas offices and hotels it means quiet hours, protected entrances and a clean site every evening.
Who installs commercial metal roofs in Irving?
Snow Roofing & Exteriors does. Here are the facts you can check:
- Owner Blake Snow brings 30 years of large commercial and industrial roofing, including the Imperial Palace casino in Biloxi in 2006, right after Hurricane Katrina, and full exterior and interior rehabs on national-brand hotel properties around the DFW Metroplex.
- Over $80 million in completed roofing projects, from small repairs to multi-million-dollar jobs, in a family roofing business that goes back 75 years.
- Our own roll formers for standing seam and R-panel in 24 or 26 gauge, with metal lead times that are typically 1 to 2 weeks.
- 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome. Snow Roofing & Exteriors is BBB A+ rated, fully insured, with references available on request.
Bidder checklist for a Irving commercial metal roof
- Panel profile, gauge (24 or 26) and paint system, in writing
- One-piece panels or end laps, and how any laps are sealed
- Clip and fastener type and spacing per the manufacturer
- Insulation, vapor control, closures and trim
- Gutters, light panels, curbs and rooftop units included or excluded
- Who pulls the Irving permit and calls for inspections
- Workmanship, panel, finish and any NDL warranty terms
What our photos show
The pictures on this page show our commercial membrane and standing seam work up close. We'll walk you through photos of buildings like yours when we meet.
We're certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. Statewide guide: commercial metal roofing. Nearby: commercial metal roofing in Dallas, commercial metal roofing in Fort Worth, 26-gauge commercial metal, and residential metal roofing in Irving.
Product names, ratings and features are as published by the manufacturer and can change. We confirm the current rating and warranty of the exact product before we order it.
Commercial warranty: a workmanship warranty from 10 years up to lifetime, depending on the job, plus both 10-year and 20-year NDL (no-dollar-limit) manufacturer warranties (the price depends on which NDL term you choose). Manufacturer coverage depends on the product and brand, and on the project qualifying for that manufacturer's program. We put the exact warranty for your roof in writing.
Certified, with 30 years installing every major roofing brand, a family roofing business going back 75 years, and over $80 million in completed roofing projects. 5.0 stars on Google at all three of our offices.
Request a free inspection or call (817) 733-9228. Small repairs are welcome too.






