Snow Roofing & Exteriors logo Call (817) 733-9228
Richardson, TX · Metal roofing

Metal Roofing in Richardson, TX

Metal roofing in Richardson, TX covers two very different houses: the low, wide mid-century ranches of the 1950s and '60s, and the two-story homes of the 1980s boom. Snow Roofing & Exteriors installs every kind of metal roof here: standing seam, stone-coated steel and metal shingles for HOA streets, copper accents, and R-panel or PBR for garages, shops and outbuildings, all in 24 or 26 gauge with standing seam and R-panel formed on our own roll formers. Our Rhome-area team is about 51 road miles (roughly 68 minutes) away. Call (817) 733-9228.
  • Hidden screws and clean, straight lines
  • Formed on our own roll formers, right on the job
  • 24 or 26 gauge steel in many colors
  • Workmanship warranty from 10 years up to lifetime, depending on the job
Illustration of a modern farmhouse with a bronze standing seam metal roof

Two building booms, two kinds of roof

Richardson sits on U.S. 75 about 14 miles north of downtown Dallas, mostly in Dallas County with a smaller piece in Collin County. The Houston and Texas Central Railroad laid out the town in 1873, and it stayed a cotton town of a few hundred people for decades. Then Collins Radio and Texas Instruments arrived after World War II. The Handbook of Texas records about 1,300 residents in 1952 and 16,810 by 1960, as additions like Richardson Heights replaced the cotton fields. A second boom came in the 1980s, when telecommunications firms built along Central Expressway and Richardson became known as the "Telecom Corridor." Census estimates show about 118,500 residents today.

Those two booms left Richardson with two housing stocks, and they don't want the same metal roof. The postwar ranches tend to be long and low, with shallow pitches, wide eaves and carports or breezeways. The 1980s and later homes are taller, steeper and cut up with hips, valleys and dormers. Here's how we usually match them:

PropertyWhat we usually recommend
1950s-60s ranch with a low pitchMechanically seamed standing seam, checked against the panel's minimum slope; it suits the long, clean rooflines
Mid-century modern with a near-flat sectionStanding seam on the pitched planes and a proper low-slope system where the roof is too flat for any steep-slope panel
1980s-90s two-story in an HOA neighborhoodStone-coated steel or metal shingles that read as shingle or shake from the curb; standing seam on porches and bays
Modern remodel or second-story additionA full standing seam roof, usually charcoal, black or dark bronze
Detached garage, carport, workshop or RV coverR-panel, PBR or corrugated, or standing seam to match the house

Every kind of metal roof, not just one

Most "metal roofing" searches in Richardson start with standing seam, but it isn't the only right answer. Here's what we install and where each one fits:

Metal systemWhat it looks likeWhere it fits best
Standing seamFlat pans with raised seams, fasteners hiddenFull roofs on modern, farmhouse and transitional homes; porch and bay accents
Stone-coated steelSteel with a stone granule finish shaped like shake, tile or shingleOwners who want metal's strength but a traditional look a neighborhood is used to
Metal shingles and metal tilePressed steel panels in shingle, slate or tile profilesHomes where the street view has to read as shingle, slate or tile
Copper accentsBright copper that weathers to brown, then greenBay windows, entry roofs, dormers and cupolas on traditional homes
R-panel, PBR and corrugatedRibbed panels with exposed screws and washersShops, barns, garages, pool cabanas, boat and RV covers

We don't quote prices on the web because pitch, size, tear-off and detail work move them too much. We'll give you a written number for each option that makes sense on your roof.

Low pitch on a mid-century house: what we check first

A low roof is where shingles struggle most, because water moves slowly and wind-driven rain gets pushed up under the laps. It's also where the wrong metal panel fails. Before we quote a metal roof on a Richardson ranch we measure the actual pitch of every plane, then pick the panel and seam the manufacturer rates for that slope. On the lowest sections that usually means a mechanically seamed panel, folded closed along its whole length. Carports and breezeway roofs that tie into the house get their own flashing details so water from the main roof doesn't dump onto a flatter section. If a section is simply too flat for any steep-slope metal, we tell you and price the right low-slope system for that part.

Older decking, re-done right

Many of Richardson's older homes are on their fourth or fifth roof, and the original plank or plywood decking has been nailed through every time. Metal is only as well attached as the wood under it, so we tear off to the deck on every metal job, re-nail or replace what won't hold a clip or screw, and show you photos of anything we replace. If the job includes new decking, the City's deck inspection is part of the schedule.

Richardson's wind record

NOAA's event narratives show Richardson's roofs take wind as seriously as hail:

  • May 28, 2024: a wind sensor at Methodist Richardson measured 83 mph, and a National Weather Service storm survey found winds up to 90 mph moved through part of the city, worst from Hillside Avenue southeast to Bowser Road south of Main Street. The same morning a tree uprooted on Claymore Drive damaged part of a home's roof.
  • March 13, 2019: emergency management reported 77 mph gusts for six minutes at the University of Texas at Dallas.
  • October 20, 2019: an EF-2 tornado in Garland, about five and a half miles away, peeled a wide section of metal roof off a warehouse and tore away the metal walls next to it.
  • June 9, 2019: broken windows at a hotel in Richardson and a 63 mph gust measured at UT Dallas.

An 83 mph measured gust and a 90 mph survey estimate are exactly the kind of wind that finds a weak edge. Metal fails at its edges and fasteners, not in the middle of the panel, so on a Richardson roof we use:

  • Tighter clip and fastener spacing at the perimeter (eaves, rakes, hips and ridge), where uplift is highest, following the manufacturer's tested pattern.
  • Trim made for the panel, hemmed and cleated, instead of face-screwed loose trim that wind can catch.
  • Deck and nailing checked after tear-off, because a metal roof is only as well attached as the wood under it.
  • Closures sized to the panel at the ridge and eaves so wind-driven rain stays out.

Hail around Richardson

NOAA's Storm Events Database lists 48 reports of hail 1.75 inches (golf-ball size) or larger within about 10 miles of the center of Richardson from 2016 through the September 2026 update, and 22 reports of hail an inch or larger within about three miles. The ones that matter most:

  • September 24, 2023: 2.25-inch hail in Richardson about a mile from the center of the city, with 2-inch and 1.75-inch hail two to three miles south the same evening.
  • April 20, 2023: 3-inch hail in Plano, about four and a half miles north.
  • April 21, 2017: 2-inch hail in Richardson, about a mile and a half from the center.
  • April 11, 2016: 2.5-inch hail in Plano about three and a half miles north, and 4.25-inch hail near Wylie, the largest within 10 miles.
  • April 27, 2026: 1.75-inch hail about a mile and a quarter from the center of Richardson, with 1.25-inch hail at several spots across the city, the most recent golf-ball-size report.

Metal isn't hail-proof. Very large hail can dent steel, and some policies treat cosmetic dents differently from leaks, so read the policy before you choose. A 24- or 26-gauge panel won't crack, curl or shed granules the way shingles do. See Class 4 metal roofs and insurance. Texas insurers must offer a premium credit for UL 2218 impact-rated roofs, but each company sets its own amount, and Class 4 earns the largest. We can't promise a discount; ask your insurer for their figure in writing. After a qualifying install we fill out TDI Form PC068 for you. If you file an insurance claim, we document the damage and meet your adjuster on the roof. Texas law requires you to pay your deductible, and a contractor may not waive, absorb or rebate it. We never will. In Texas you generally have 1 year from the date of loss to file; check your policy.

City of Richardson roof permit

Richardson draws its permit line by the size of the job. The City's roof repair and replacement page says a permit is required for any roof replacement, recovering or repair that exceeds 25% of the total roof area, so a full re-roof always needs one. The rest of the rules, from the City's own pages:

  • Approved and posted first. The permit has to be approved and posted at the property before any work starts.
  • Two inspections when there's decking. An inspection is required when the roof deck is installed (if the job includes decking) and a final inspection when the roof is complete.
  • Registered contractors only. Per the City's contractor registration page, every contractor has to be registered before a permit is issued; registration runs one year. You can check any roofer against the City's Registered Contractors List before you sign.
  • Current codes. Richardson has adopted the 2021 International Codes, and the permit exists, in the City's words, to make sure the proper codes are followed.

Inspections are run twice a day, per the City's building inspection FAQ, so a deck inspection doesn't usually hold a crew up for long. Questions about a specific address go to Richardson Building Inspection at 972-744-4180. We register, apply, post the permit and schedule the inspections.

For a metal roof, the 25% line means a full conversion always needs a permit, and a decking inspection if we replace sheathing. We write both into the schedule so the panels go on as soon as the deck passes.

Getting metal past an HOA in Richardson

Many neighborhoods in Richardson have an HOA, and committees mostly care about how the roof reads from the street and whether the color fits the neighborhood. Stone-coated steel and metal shingles read as shake, shingle or tile from the curb; standing seam is often approved first on porches, bays and entries. We put together the product sheet, color chip, profile drawing and impact rating so the committee can decide on the first pass. Approval is always up to your HOA.

Carports, garages and shops

A lot of Richardson's older lots have a carport, detached garage or workshop behind the house. We re-panel and re-roof them in R-panel, PBR or standing seam, color-matched to the house, and metal lead time is typically 1 to 2 weeks. Our crews also handle siding, gutters and windows, so one crew can finish the whole exterior.

Why it matters that we form our own panels

  • One piece from eave to ridge. We cut standing seam and R-panel to the length of each roof plane, so long runs don't need mid-slope laps.
  • 24 or 26 gauge on every standing seam and R-panel roof. See 26 vs. 29 gauge.
  • No waiting in a panel shop's queue after a hailstorm, when everyone needs a roof at once. Metal lead time is typically 1 to 2 weeks.
  • Flashings bent for the panel, not caulked: walls, chimneys, valleys, skylights and pipes.
  • Every inspection comes with a free digital photo report, so you see what we see.

How a metal roof job runs with us

  1. Inspection and free digital photo report: deck, ventilation, penetrations, valleys and measurements.
  2. Written spec for each option: system, gauge, profile, color, underlayment, trim and every flashing detail.
  3. Approvals: the HOA or historic-review packet if you need one, then the permit.
  4. Tear-off and deck repair where needed, then high-temperature synthetic underlayment made for metal.
  5. Install by our own crew, with hips, ridges, eaves and penetrations detailed for the system.
  6. Final walk-through, a magnet sweep of the yard and driveway, and your warranty in writing.

Who installs metal roofs in Richardson?

Snow Roofing & Exteriors does. Here are the facts you can check before you call anyone:

  • 75 years as a family roofing business, and 30 years in the business for owner Blake Snow, who is still on the roofs.
  • Over $80 million in completed roofing projects, from small repairs to multi-million-dollar jobs.
  • 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome.
  • Our own roll formers for standing seam and R-panel, in 24 or 26 gauge, with metal lead times that are typically 1 to 2 weeks.
  • Our own crew, about 51 road miles (roughly 68 minutes) from Richardson with our Rhome-area team.
  • Snow Roofing & Exteriors is BBB A+ rated.

Our metal work, up close

The photos on this page show our roof work up close. We never show a street or address.

We're certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. We give a workmanship warranty from 10 years up to lifetime, depending on the job, and the manufacturer warranty on the panel and finish, in writing.

More in Richardson: metal roofing in Richardson, standing seam in Richardson and our Richardson roofing page. Nearby: metal roofing in Plano, Allen, Carrollton and storm damage in Plano.

Product names, ratings and features are as published by the manufacturer and can change. We confirm the current rating and warranty of the exact product before we order it.

Residential warranty: a workmanship warranty from 10 years up to lifetime, depending on the job, with manufacturer warranties up to lifetime. Manufacturer coverage depends on the product and brand, and on the project qualifying for that manufacturer's program. We put the exact warranty for your roof in writing.

Certified, with 30 years installing every major roofing brand, a family roofing business going back 75 years, and over $80 million in completed roofing projects. 5.0 stars on Google at all three of our offices.

Request a free inspection or call (817) 733-9228. Small repairs are welcome too.

Charcoal standing seam metal roof on a brick ranch home near Rhome, TX
Charcoal standing seam on a brick ranch
Dark bronze standing seam metal roof replacing shingles on a red brick ranch home near Sanger, TX
Dark standing seam replacing shingles on a brick ranch
Standing seam metal roof on a blue board-and-batten wing of a ranch estate
Standing seam on a board-and-batten wing
Close-up of a gray standing seam metal roof with matching painted vent stacks and pipe flashings
Gray standing seam with painted vent stacks and pipe flashings
Side elevation of a brick home with multiple hips in standing seam metal
Multiple hips in standing seam
Detail of a shake-to-standing-seam metal transition
Where a shake roof meets standing seam
Close view of standing seam panels at the eave of a brick ranch home
Seams running straight to the eave
Snow Roofing crew at the panel trailer beside a brick garage during a standing seam install
Our crew and panel trailer on install day

Frequently asked questions

Who installs metal roofs in Richardson?

Snow Roofing & Exteriors installs standing seam, stone-coated steel, metal shingle, copper accent, R-panel and PBR roofs on homes, carports, garages and shops in Richardson. It is a family roofing business that goes back 75 years, owner Blake Snow has 30 years in the business, the company has completed over $80 million in roofing projects, it is BBB A+ rated, and it has 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome. Standing seam and R-panel are formed on its own roll formers in 24 or 26 gauge. Its Rhome-area team is about 51 road miles (roughly 68 minutes) away. Call (817) 733-9228.

Do I need a permit for a metal roof in Richardson?

Yes for a full roof. Richardson requires a permit for any roof replacement, recovering or repair that exceeds 25% of the total roof area. The permit has to be approved and posted before work starts, and the contractor has to be registered with the City.

What inspections does Richardson do on a re-roof?

An inspection when the roof deck is installed, if the job includes decking, and a final inspection when the roof is complete. The City runs inspections twice a day, and we schedule them.

Can metal go on my low-pitch ranch roof?

Usually, yes. We measure every plane and use a mechanically seamed standing seam panel rated for that slope. If a section is too flat for any steep-slope roof, we quote a low-slope system for that part.

Has Richardson had big hail?

Yes. NOAA lists 48 reports of hail 1.75 inches or larger within about 10 miles from 2016 through September 2026, including 2.25-inch hail about a mile from the center of the city on September 24, 2023.

Will a metal roof hold up to Richardson wind?

When the edges are done right, yes. On May 28, 2024 a sensor at Methodist Richardson measured 83 mph and a National Weather Service survey found winds up to 90 mph. We tighten clip and fastener spacing at the perimeter to the manufacturer's tested pattern.

How do I check that a roofer is registered in Richardson?

The City publishes a Registered Contractors List and requires every contractor to be registered before a permit is issued. You can also call Building Inspection at 972-744-4180.

Is standing seam the only metal option?

No. We also install stone-coated steel and metal shingles or tile for a traditional look, copper accents, and R-panel, PBR or corrugated on shops, barns and covers.

What gauge metal do you install?

24 or 26 gauge steel on every standing seam and R-panel roof. We don’t install 29 gauge on homes.

How soon can a metal roof start?

Metal lead time is typically 1 to 2 weeks, because we form standing seam and R-panel on our own roll formers. HOA approval and the permit can add time, so we start that paperwork right after you sign.

What warranty do you give on a metal roof?

A workmanship warranty from 10 years up to lifetime, depending on the job, plus the manufacturer warranty on the panel and finish, in writing.

Get a free estimate

Tell us how to reach you. Blake or the team will call you back.

Or call (817) 733-9228 snowexteriors@gmail.com