A Southlake office building or Frisco retail center usually has two roofs. One is the roof people see: towers, mansards, entry canopies and covered walkways. The other is the big flat roof behind the parapet, full of HVAC units, that nobody sees until it leaks into a tenant’s space. Picking the right system for each one, and doing the work without shutting down the tenants, is most of the job.
I’m Blake Snow. I’ve been roofing for 30 years, and we do commercial roofing across Southlake, Frisco, Westlake, Colleyville and the rest of DFW, including full exterior rehabs on national-brand hotel properties. Here’s how I’d think about a commercial roof on a high-end office or retail property.
The short version
| Roof area | Our first choice | Other good options | Why |
|---|---|---|---|
| Towers, mansards, canopies (visible) | Standing seam metal, formed on site on our own roll formers | Stone-coated steel, tile or synthetic to match the center’s design | Clean lines, color to match the brick and stone, long life, hail-resistant |
| Flat roof, office or plain retail | TPO | PVC, modified bitumen | Reflective, heat-welded seams, cost-effective at large square footage |
| Flat roof, restaurants and grease exhaust | PVC | TPO with grease protection at the fans | PVC generally handles grease and many chemicals better than TPO |
| Flat roof that’s dry but aging | Restoration coating (silicone or urethane systems) | Recover with a new membrane | Less tear-off, less disruption, if the roof qualifies |
| Low-slope metal roof that’s sound but rusting at fasteners | Metal restoration system | Retrofit standing seam | Seals fasteners and seams without tearing off |
The visible roof: why we push standing seam
On a Southlake or Frisco center, the towers, mansards and canopies are part of the brand. They have to look sharp from the parking lot for decades. That’s where standing seam metal shines:
- We form it ourselves. We run our own roll formers for standing seam and R-panel, so each panel is formed on the jobsite to the measured length of each run. Panels are 24 or 26 gauge, and our metal lead time is typically 1 to 2 weeks.
- Color to match the masonry. Bronze, black, gray and other finishes pick up the stone and brick on most new centers. See metal roof colors and finishes.
- Snap-lock vs. mechanically seamed. Steep mansards and towers can do well with snap-lock. Low-slope canopies and roofs often need a mechanically seamed double-lock panel. Details: snap-lock vs. mechanically seamed for commercial buildings.
- Slope. The International Building Code sets 1/4:12 as the minimum slope for standing seam metal roof systems, but each panel has its own published minimum, often higher. We go by the panel’s data.
More: commercial metal roofing, standing seam in Southlake and standing seam in Frisco.
The flat roof: TPO, PVC or restoration
The IBC also sets 1/4:12 as the minimum slope for single-ply membranes like TPO and PVC. A lot of older flat roofs don’t drain that well, and ponding water is where they fail first. Every flat roof bid should start with drainage: tapered insulation, crickets between drains, and drains and scuppers that are actually big enough.
TPO is the most common choice on offices and plain retail. It’s white and reflective, the seams are heat-welded, and it comes in 45, 60 and 80 mil. Thicker membranes generally qualify for longer warranties and hail coverage. Example: Carlisle Sure-Weld TPO in Southlake and Frisco.
PVC is our usual pick over restaurants, because it generally holds up to grease and many chemicals better than TPO. See Sika Sarnafil PVC in Frisco.
Restoration coatings can add years to a flat roof that’s still dry and sound, often with less tear-off and less disruption for tenants. We’re an American WeatherStar Approved Contractor, and we also install our own private-label EpoxyFlex coating. See American WeatherStar systems for Frisco commercial roofs and our roof coatings page.
Tear off, recover or coat? What the code allows
The 2021 International Building Code (Section 1512) decides a lot of this for you. It allows a recover in several cases, including:
- A new covering installed per the maker’s approved instructions
- A complete, separate system like standing seam that carries its loads to the structure, not the old roof
- A new coating over an existing coating, metal panels, built-up roof, spray foam, modified bitumen, or TPO/PVC/EPDM single-ply
It does not allow a recover where:
- The existing roof is water-soaked or deteriorated to the point it can’t serve as a base
- The existing covering is slate, clay, cement or asbestos-cement tile
- The roof already has two or more roof coverings
That’s why we do a moisture survey before recommending a coating or recover. Our drone inspections are flown by an FAA-certified pilot, and infrared scans help find wet insulation. If a big share of the roof is wet, coating it just seals the water in.
Warranties
- Workmanship: in writing on every job, from 10 years up to lifetime, depending on the job.
- Manufacturer NDL warranties: 10- and 20-year no-dollar-limit warranties are available on qualifying systems. The manufacturer inspects the roof before issuing one. See NDL warranties on commercial roofing.
- Hail coverage: some membrane makers offer it as an add-on, usually tied to a thicker membrane and an approved cover board. It has to be specified before the bid, not after the storm.
Working around tenants
On an occupied center, the schedule matters as much as the system:
- Phase the work so each tenant is only affected for a short window, and dry-in every section at the end of each day.
- Plan crane picks and material staging around store hours and parking.
- Coordinate with the HVAC contractor for unit disconnects and curb work.
- Protect storefronts, walkways and cars, and keep a clean site every day.
- Give the property manager a daily photo update.
Southlake and Frisco permits
- Frisco: the city lists roofs among its commercial building permits, filed electronically through eTRAKiT. Frisco’s code requires contractors, specifically including re-roofing contractors, to be registered with the city before a permit is issued, with liability insurance naming the City of Frisco as certificate holder.
- Southlake: the city’s When is a permit required? list includes replacing roofing materials, and contractors must be registered with the city.
We pull the permits and schedule the inspections. Retail centers and office parks may also have owner or association design standards for roof color and metal. Get those approvals first.
After hail
Southlake and Frisco both get hail. You can look up past storms in NOAA’s Storm Events Database. Hail can bruise a membrane without an obvious hole, so a good inspection includes close-up photos and, where needed, core cuts or moisture checks. In Texas you generally have 1 year from the date of loss to file a claim, but check your policy. See storm damage.
12 questions to ask before you sign
- Which areas get metal, which get membrane, and why?
- Who forms the metal panels, and what gauge and finish are they?
- What’s the panel’s published minimum slope, and what’s the slope on my roof?
- TPO or PVC? What thickness? Why that one for my tenants?
- How will you fix the drainage, not just cover it?
- Did you do a moisture survey? What percentage of the roof is wet?
- Tear off, recover or coat, and does the code allow it here?
- What manufacturer warranty, how many years, and is it NDL?
- Is hail coverage included, and what does it require?
- How will you phase the work around tenants and store hours?
- Who handles the permit and city registration?
- What does your workmanship warranty cover, in writing?
Related pages
- Commercial roofing
- Commercial roofing in Southlake and Frisco
- Commercial metal roofing
- Roof coatings
Talk to us about your Southlake or Frisco commercial roof
We roof office buildings, retail centers, restaurants and hotels in Southlake, Frisco, Westlake, Colleyville and across DFW. Every roof is installed to manufacturer specs by certified installers. We’re certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. We’re fully insured and BBB A+ rated, with 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome. Request a free inspection or call (817) 733-9228.
Sources
- International Code Council via UpCodes: 2021 IBC Section 1512.3, Roof recover
- Polyisocyanurate Insulation Manufacturers Association: 2021 IBC/IECC reroofing compliance checklist
- International Code Council: 2021 IBC Chapter 15, Roof Assemblies and Rooftop Structures
- City of Frisco: Apply for Commercial Permits
- City of Frisco: Contractor Registration Information
- City of Frisco Code, Chapter 18, Article II: Contractor Registration
- City of Southlake: When is a permit required?
- NOAA NCEI: Storm Events Database

