Snow Roofing & Exteriors logo Call (817) 733-9228
Blog

Sherwin-Williams UNIFLEX Roof Coatings on Fort Worth Commercial Roofs: Silicone44 vs. Silicone22 vs. Urethane88 vs. Elastomeric Acrylic

By Blake Snow, owner ·

Illustration of an aerial view of a suburban strip center with a bright white coated flat roof and a full parking lot
Illustration

Fort Worth has a lot of roofs that are good coating candidates: warehouses up the north side, strip centers along the main corridors, small office and medical buildings, and metal shops on the edges of town. Many owners already know the Sherwin-Williams name from paint, so when UNIFLEX shows up on a bid, the next question is fair: what is it, which UNIFLEX coating, and is it the right one for this roof?

I’m Blake Snow. I’ve been in roofing for 30 years, and we’ve applied many brands of roof coatings, Sherwin-Williams’ UNIFLEX line among them. This post walks through the current UNIFLEX lineup using UNIFLEX’s own September 2026 product portfolio and product pages, then tells you how I’d match the products to Fort Worth buildings.

The short answer

  • Roof ponds water? Look at Silicone44, UNIFLEX’s high-solids 100% silicone.
  • Roof sees foot traffic, impact or abrasion, and drains well? Urethane88 (gray base, white finish) is the tough one.
  • Roof drains well, budget matters, and you want a bright white acrylic? Premium Elastomeric or Commercial Grade Elastomeric over the right basecoat and primer.
  • Silicone22 is the lower-solids silicone. It’s listed for ponding water too, but you get less coating per gallon, so check the mil thickness on any bid that uses it.

Who UNIFLEX is

UNIFLEX calls itself a Sherwin-Williams business unit, and its 2026 portfolio lists a Cleveland, Ohio address. The line covers fluid-applied roof systems: reflective white coatings, colored coatings, aluminum coatings, asphalt emulsions, basecoats and primers, and sealants and patching products. Its pitch is the same as most coating makers: restore a sound roof without a tear-off, add a reflective surface, and recoat later instead of re-roofing.

The reflective white coatings, side by side

Silicone44 WhiteSilicone22 Low-Solid WhiteUrethane88 WhitePremium Elastomeric WhiteCommercial Grade Elastomeric White
Chemistry100% silicone, moisture cureSilicone, low solidsAliphatic moisture-cure polyurethane100% acrylic elastomeric100% acrylic elastomeric
Solids by volume95%68%78% (±2)Per data sheetPer data sheet
Dry film (published)30 mils at 5 gal per 250 sq ft22 mils at 5 gal per 250 sq ft12.5 mils at 1 gal per 100 sq ftPer data sheetPer data sheet
Recoat6 hours minimum24 hours4 hoursPer data sheetPer data sheet
Full cure72 hours24-48 hours72 hoursPer data sheetPer data sheet
Ponding waterListed for ponding waterListed for ponding waterListed as resisting ponding water in a watertight systemNot listed for ponding waterNot listed for ponding water
VOC (published)10 g/L or less (product page)246 g/L or less134.5 g/L50 g/L or lessUnder 50 g/L
Packaging5 gal, 55 gal5 gal5 gal5 gal, 55 gal, 250 gal tote5 gal, 55 gal, 250 gal tote

Sources: UNIFLEX product portfolio (Sept. 2026) and product pages for Silicone44, Silicone22 and Urethane88. Values are UNIFLEX’s typical published values.

The solids line is the one to look at. Solids are what stays on the roof after the coating cures. At the same 5 gallons per 250 sq ft, UNIFLEX lists 30 dry mils for Silicone44 and 22 for Silicone22. If two bids both say “silicone,” ask which one, and how many dry mils.

Colors, aluminum and asphalt products

Beyond white, UNIFLEX lists Silicone44 Color (gray, tan, yellow, blue, black, green, medium gray and red in its part list), CoolMax41 Hi-Build Elastomeric white (UNIFLEX says it’s formulated for desert climates), Premium Elastomeric Sedona Tan and black, and tint bases matched to Sherwin-Williams’ Sher-Color palette. That’s useful when a coated roof shows from the street or needs to match a brand color.

UNIFLEX also makes aluminum roof coatings (500 Premium, 300 Commercial and 204XB) and asphalt emulsions. These are maintenance products for asphalt roofs, not the same thing as a reflective elastomeric restoration system.

Basecoats and primers: where coating jobs are won or lost

UNIFLEX’s basecoat and primer lineup tells you how seriously they take prep:

  • Urethane88 Gray basecoat under the white Urethane88 finish.
  • Premium Elastomeric Gray and Commercial Grade Elastomeric Gray, which can be basecoats over metal, concrete and foam.
  • Single Ply Elastomeric Acrylic Gray Basecoat for weathered EPDM, Hypalon, TPO and other approved single-ply roofs (must be topcoated with a UNIFLEX elastomeric finish).
  • Elastomeric MB Basecoat for smooth built-up, mod-bit and granulated cap sheet roofs (must be topcoated).
  • Primers: Rust Inhibitive Metal Primer, Acrylic Rust Inhibitive Primer, Acrylic Concrete Primer, Bond-It Wash Primer (a cleaning primer for EPDM) and Bleed Blocker Primer, a waterborne epoxy UNIFLEX says is designed to prevent asphalt bleed-through.

UNIFLEX’s Silicone44 page says EPDM must be primed with a bonding primer for EPDM, and that TPO, PVC, metal or asphalt may need primer, decided by an adhesion pull test. On our jobs, pull and adhesion tests are usually done with the manufacturer’s rep, who meets our crew on site.

Warranties: Materials vs. UNIGUARD

UNIFLEX’s warranty options sheet (rev. 6/2025) describes two kinds:

  • UNIFLEX Materials warranty: replaces UNIFLEX materials proven defective. Standard terms are 7, 10 or 15 years based on product and substrate. No charge. It does not cover repair labor or workmanship.
  • UNIGUARD System warranty: covers UNIFLEX materials in the coating system plus the labor to install replacement UNIFLEX materials. It requires installation to UNIFLEX specs by a UNIFLEX Authorized Contractor, pre-approval through UNIFLEX’s contractor warranty portal, and a warranty fee. It does not cover workmanship or failures from improper installation.

If a bid promises a UNIGUARD warranty, ask to see the pre-approval. On our commercial bids we offer 10-year and 20-year NDL (No Dollar Limit) warranty options at different prices, depending on the system, and our own workmanship warranty runs from 10 years up to lifetime, depending on the job. We’ll show you exactly which warranty backs which system.

Which UNIFLEX product I’d look at, building by building

Your Fort Worth buildingWhat I’d usually look atWhy
Warehouse or strip center with ponding spotsSilicone44 at a thickness that matches the warrantyHigh solids, listed for ponding water
Roof with heavy HVAC service traffic, good drainageUrethane88 gray base + white finishTough two-coat urethane system
Metal shop or warehouse with surface rust, good slopeRust Inhibitive primer, seam and fastener details, Premium ElastomericAcrylic over primed metal sheds water well
Older granulated mod-bit or smooth built-up roofBleed Blocker Primer, then Elastomeric MB Basecoat and an elastomeric finish, or silicone if it pondsStops asphalt staining, matches the substrate
Weathered TPO or EPDM that tests drySingle Ply Elastomeric Acrylic Gray Basecoat + finish, or Silicone44 with the right primerPrimer and basecoat built for single-ply
Wet insulation, failing deckNo coating. Repair or re-roofCoatings don’t fix wet roofs

These are starting points. The drainage, the existing roof, the warranty you need and your budget decide the final spec. We also offer EpoxyFlex, our own private-label roof coating, and we’re an American WeatherStar Approved Contractor, so we can price more than one system side by side. See my American WeatherStar post and Tropical and SOPREMA coatings post for other options.

What to ask before you sign a UNIFLEX coating bid

  1. Which exact UNIFLEX product (Silicone44, Silicone22, Urethane88, Premium or Commercial Grade Elastomeric)?
  2. How many gallons per square and dry mils?
  3. Which basecoat and primer, and was an adhesion pull test done?
  4. Was a moisture survey done? How will wet areas be replaced?
  5. How are seams, fasteners, curbs, drains and the metal edge detailed?
  6. Is the warranty a Materials warranty or a UNIGUARD System warranty? How many years?
  7. If UNIGUARD, is the contractor UNIFLEX Authorized, and is the pre-approval done?
  8. What’s the plan if rain moves in between coats?
  9. What maintenance does the warranty require?
  10. Who handles repairs if the roof leaks in year two?

After a storm

A coating is not a hail repair. Get the roof inspected and documented before anyone coats over it. Our commercial hail claims page covers what to photograph and record, and our FAA-certified drone pilot can fly the roof for a full overview. In Texas you generally have 1 year from the date of loss to file a claim, but check your policy.

Talk to us about a roof coating in Fort Worth

We coat and restore commercial roofs across Fort Worth, Haltom City, North Richland Hills, Saginaw, White Settlement, Benbrook and Lake Worth. We’re certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. We’re fully insured, BBB A+ rated, and references are available on request.

See our commercial roof coatings and Fort Worth commercial roofing pages, use the estimate form below, or call (817) 733-9228.

Frequently asked questions

Is UNIFLEX made by Sherwin-Williams?

Yes. UNIFLEX describes itself as a Sherwin-Williams business unit, and Sherwin-Williams sells UNIFLEX roof coatings. UNIFLEX's September 2026 product portfolio covers reflective white, pigmented and aluminum roof coatings, asphalt emulsions, basecoats, primers, sealants and patching products.

What is the difference between UNIFLEX Silicone44 and Silicone22?

Silicone44 is UNIFLEX's high-solids 100% silicone coating: UNIFLEX lists 95% solids by volume and 30 dry mils at 5 gallons per 250 sq ft. Silicone22 is a low-solids silicone: 68% solids by volume and 22 dry mils at the same rate, with a longer 24-hour wait between coats. Both are listed for ponding water. For a commercial roof, more solids means more coating left on the roof per gallon.

When does UNIFLEX Urethane88 make sense?

Urethane88 is a single-component aliphatic moisture-cure polyurethane. UNIFLEX lists high tensile strength, high elongation, dirt-pickup resistance and a two-coat system (gray base, white finish). Urethanes are tough, so I look at them for roofs with more foot traffic or where impact and abrasion matter. Note its VOC is listed at 134.5 g/L, higher than the water-based and silicone products.

Do UNIFLEX coatings need a primer?

Often. UNIFLEX says EPDM roofs must be primed with a bonding primer for EPDM before Silicone44, and that TPO, PVC, metal or asphalt may need primer, decided by an adhesion pull test. Its lineup includes Rust Inhibitive Metal Primer, Acrylic Rust Inhibitive Primer, Acrylic Concrete Primer, Bond-It Wash Primer and Bleed Blocker Primer for asphalt surfaces.

What's the difference between a UNIFLEX Materials warranty and a UNIGUARD System warranty?

Per UNIFLEX's warranty options sheet, a Materials warranty covers replacement of defective UNIFLEX materials only, typically 7, 10 or 15 years depending on product and substrate, with no labor or workmanship coverage and no charge. A UNIGUARD System warranty also covers the labor to install replacement UNIFLEX materials, but requires a UNIFLEX Authorized Contractor, pre-approval by UNIFLEX Technical and a warranty fee. Neither covers workmanship.

Can I just buy UNIFLEX at a store and roll it on myself?

Some UNIFLEX products are sold through retail locations, and they're fine for small patches. On a commercial roof, the coating is the easy part. The cleaning, moisture survey, adhesion testing, primers, seam and penetration details and correct mil thickness are what decide whether it lasts, and they're what a warranty depends on.

Get a free roof inspection

We get on the roof, photograph what we find, and tell you plainly whether you need a repair or a replacement.

Get a free estimate

Tell us how to reach you. Blake or the team will call you back.

Or call (817) 733-9228