Snow Roofing & Exteriors logo Call (817) 733-9228
Blog

Inland AldoCoat 400S Acrylic vs. AldoThane 384/386 Polyurethane Roof Coatings for Decatur Commercial and Metal Buildings

By Blake Snow, owner ·

Illustration of a long white-coated ribbed metal warehouse roof on open North Texas land
Illustration

Around Decatur and the rest of Wise County, most commercial roofs I get called to aren’t glass office towers. They’re metal shops, ag barns, oilfield and equipment yards, church fellowship halls, and small warehouses, plus a few low-slope roofs behind parapets on the Square and along US 287. A lot of them don’t need a new roof. They need the fasteners and seams fixed and a good coating on top.

I’m Blake Snow. I’ve been roofing for 30 years. I already wrote about Karnak’s silicone and acrylic coatings for Decatur metal roofs. This post covers a different choice from another maker: Inland Coatings’ AldoCoat 400S acrylic versus its AldoThane polyurethanes, the 384 base coat and the 386 finish coat. Every number below comes from Inland’s current data sheets and design guidelines.

First: AldoCoat and AldoThane are Inland products now

These names come from ALDO Products of North Carolina. ALDO became part of Inland Coatings in 2019, and in early 2025 ALDO, TRUCO and Inland were combined under one brand, Inland. The AldoCoat and AldoThane names are still in Inland’s 2026 catalog and data sheets. If a bid says “ALDO,” it’s the same family, now sold as Inland Coatings.

The short answer

  • Budget-friendly reflective coating on a metal shop or barn that drains well: AldoCoat 400S acrylic. Water-based, low-VOC, soap-and-water cleanup.
  • Roofs that take foot traffic, equipment, or hail, or that hold a little water: AldoThane 386 aliphatic urethane, often over the AldoThane 384 base coat. Much tougher film.
  • Want a silicone finish with a hard base under it? Inland’s hybrid schedule puts AldoThane 384 under AldoSil 397 silicone.
  • Already silicone-coated? Neither AldoThane product goes over existing silicone. Inland says so on both data sheets.

AldoCoat 400S vs. AldoThane 384 vs. AldoThane 386: Inland’s numbers

AldoCoat 400SAldoThane 384AldoThane 386
What it isWater-based elastomeric acrylicAromatic polyurethane base coatAliphatic polyurethane roof coating
CureWater evaporationMoisture cureMoisture cure
Solids by weight / volume68% / 53%75% / 82%83% / 88%
Weight per gallon12 lb9 lb11.2 lb
Elongation (ASTM D2370)250%209%325%
Tensile strength (ASTM D2370)275 psi359 psi1,500 psi
VOCUnder 50 g/LUnder 250 g/LUnder 240 g/L
Solar reflectance / SRI (white, initial)0.87 / 110Not listed (aluminum-gray)0.81 / 101
Standard colorsWhite, tan, gray, customAluminum-grayWhite, gray
Typical minimum applicationTwo coats at 24 wet milsOne base coat at 20 wet milsOne coat at 32 wet mils, or two at 20
Weather window after applicationNo rain, dew or freezing within 24 hrsNo rain, dew or freezing within 8 hrsNo rain, dew or freezing within 8 hrs
Shelf life18 months6 months1 year
CleanupWarm water and soapXyleneXylene

Sources: Inland’s AldoCoat 400S, AldoThane 384 and AldoThane 386 technical data sheets. Inland notes results may vary by ±10%.

What the differences mean on a Wise County roof

Toughness. The biggest gap in that table is tensile strength: 1,500 psi for AldoThane 386 against 275 psi for AldoCoat 400S. Urethanes are the coatings you pick when people walk the roof to service HVAC units, when equipment sits up there, or when you want a harder film against hail. Acrylics are softer.

Ponding water. Inland’s 400S data sheet says plainly: do not use on roof areas subject to ponding water. Its acrylic guideline for smooth BUR and mod bit says that where ponding can’t be fixed, those areas get AldoSil 397 silicone instead. Inland’s urethane guideline for smooth BUR and mod bit, by contrast, adds an extra 16 wet mils of polyurethane in ponding areas, extended at least 12 inches past them. Metal roofs usually shed water, but low-slope roofs behind parapets often don’t.

Weather. 400S cures by evaporation and needs a 24-hour window with no rain, dew or freezing. The AldoThane products cure with moisture in the air and need 8 hours. In a Wise County spring, that difference can decide whether a job finishes this week.

Why 384 is a base coat. 384 is an aromatic urethane in aluminum-gray. Inland sells it as a base coat to be topcoated with AldoThane 386 or AldoSil 397 within 48 hours. Inland’s own literature describes 386 as the UV-stable one, so don’t leave 384 exposed as a finish.

Reflectance. White 400S lists SRI 110 initial; white 386 lists SRI 101. Both are cool roofs compared to bare Galvalume or rust.

Odor and cleanup. 400S is water-based, low-VOC, and cleans up with soap and water. The urethanes are solvent-borne and clean up with xylene. On a building that stays open during the work, we plan intakes and timing around that.

Inland’s coat schedules for metal roofs

From Inland’s metal roof design and application guidelines (minimums, not averages):

System warrantyAcrylic (AldoCoat)Polyurethane (AldoThane 386)Hybrid (AldoThane 384 + AldoSil 397)
10-year400S 1.25 + 1.25 gal/100 sq. ft. (min. 21 dry mils)386 1.0 + 1.0 gal/100 sq. ft. (min. 28 dry mils)384 1.25 + 397 1.0 gal/100 sq. ft. (min. 31 dry mils)
15-year400S 1.5 + 1.5 (min. 25 dry mils)386 1.25 + 1.25 (min. 35 dry mils)384 1.25 + 397 1.5 (min. 38 dry mils)
20-year400S 1.25 + 400S 1.25 + TE+ 1.25 (min. 31 dry mils)386 1.0 + 1.0 + 1.0 (min. 42 dry mils)384 1.25 + 397 2.0 (min. 46 dry mils)

Sources: Inland’s acrylic, polyurethane and silicone/polyurethane metal roof guidelines.

Inland also lists a typical dry time between coats of 12 to 24 hours for acrylic and 12 to 18 hours for polyurethane. Inland’s guidelines say warranty applications must be submitted before the project begins, system warranties cover full roof areas, edge metal and gutters are excluded, and system warranties aren’t available on residential projects. On the data sheets themselves, Inland’s product warranty covers replacement of defective material, so ask for the system warranty in writing if that’s what you’re paying for.

How a proper Inland metal-roof job goes

Inland’s metal guidelines match how we already work:

  1. Inspect the panels, purlins and drainage. Dented panels that hold water get repaired or replaced.
  2. Fasteners. Every screw is tightened or replaced with an oversized screw and neoprene washer, then encapsulated in mastic (AldoSeal 750 acrylic mastic for the acrylic system, AldoThane 385 for the urethane system).
  3. Seams. Inland says any opening wider than 1/16 inch between panels, flashings or penetrations must be closed or made flush with additional fastening first; then horizontal seams get mastic or a 4-inch fabric strip set in coating.
  4. Rust. Wire brush loose scale, optionally treat with RRC-600, then prime sound rusted areas with AldoPrime 710 at about 0.5 gallons per 100 sq. ft. (two coats on medium to heavy rust). Both 400S and the AldoThane data sheets say rusted metal must be primed before coating.
  5. Clean. A pressure washer with at least 3,000 psi working pressure. Coatings don’t stick to chalk, dust or oil.
  6. Coat by the gallon, checked with a wet-film gauge. Inland reminds contractors to account for the extra surface area of ribbed panels, and to give vertical ribs extra coats so they get full coverage.

One more equipment note from the data sheets: 400S shouldn’t go through hoses used for silicone. Keep the chemistries separate.

When a coating is the wrong answer

  • Rusted-through panels or failing purlin connections. That’s a re-panel. We run our own roll formers for 24- and 26-gauge R-panel and standing seam, and offer PBR and corrugated panels, with a typical lead time of 1 to 2 weeks. See our barn roofing page for Decatur.
  • Wet insulation on a low-slope roof. Coating traps it. We check moisture first.
  • Hail damage that hasn’t been documented. Get it inspected first. Our FAA-certified drone pilot can fly the roof; see our drone roof inspection page.

More on that decision on our roof coating vs. replacement page.

Other coatings we bid side by side

We’re certified with Mule-Hide and Tropical Roofing Products, both of which make coatings, we’re an American WeatherStar Approved Contractor, and we offer EpoxyFlex, our own private-label roof coating. For more comparisons, see my Inland AldoSil 397 vs. 395 silicone post, my Mule-Hide silicone vs. acrylic post and my Sherwin-Williams Uniflex post.

Questions to ask before you sign a coating bid

  1. Is it AldoCoat 400S, AldoThane 386, or a 384 + 397 hybrid, and why?
  2. How many coats and gallons per 100 sq. ft., and what minimum dry film?
  3. Does the roof pond anywhere? If so, what goes in those areas?
  4. Is there any existing silicone on the roof? (If yes, AldoThane is out.)
  5. How are fasteners, seams and rust handled, and which primer?
  6. Which Inland system warranty, how many years, and was it applied for before work starts?
  7. What’s the weather window, 24 hours or 8, and what’s the plan if rain shows up?
  8. How will rooftop intakes and odor be handled if the building stays open?

After a storm

Check Wise County storm history in the NOAA NCEI Storm Events Database, and get any hail damage inspected and documented before a coating goes on. In Texas it’s generally 1 year from the date of loss to file a claim, but check your policy.

Talk to us about a coating in Decatur

We coat and restore metal and low-slope roofs across Decatur, Bridgeport, Alvord, Paradise, Boyd, Chico and Rhome. We’re certified with GAF, CertainTeed, Owens Corning, Atlas, Johns Manville, Carlisle, Tropical Roofing Products, Mule-Hide and Enviroshake, and many other roof manufacturers. Commercial jobs can carry 10- and 20-year NDL warranties, and our workmanship warranty runs from 10 years up to lifetime, depending on the job. We’re fully insured, BBB A+ rated, and have 5.0 stars on Google at all three offices: Bridgeport, Decatur and Rhome.

See our acrylic coating page, urethane coating page, metal roof coating page and Decatur commercial roofing page, use the estimate form below, or call (817) 733-9228.

Sources

Frequently asked questions

What's the difference between AldoThane 384 and AldoThane 386?

AldoThane 384 is a single-component, moisture-cure aromatic polyurethane base coat in aluminum-gray. Inland says it can be topcoated with AldoThane 386 or AldoSil 397. AldoThane 386 is a single-component, moisture-cure aliphatic polyurethane roof coating in white or gray that Inland describes as UV-stable; it can be the finish coat over 384 or used on its own. 386 lists 1,500 psi tensile strength and 325% elongation on Inland's data sheet.

Is AldoCoat 400S or AldoThane better for a metal building?

It depends on the roof. AldoCoat 400S is a water-based acrylic that's easy to work with and cleans up with soap and water, but Inland says not to use it where water ponds. AldoThane 386 is a tougher, solvent-borne urethane with much higher tensile strength, which suits roofs with foot traffic or hail exposure. On a well-drained metal shop, either can be the right call; we decide after inspecting the panels, drainage and how the building is used.

Can you put AldoThane over an old silicone coating?

No. Inland's AldoThane 384 and 386 data sheets both say do not apply over existing silicone coatings. Once a roof is silicone, recoating is normally done with silicone.

How many coats does an Inland acrylic or polyurethane metal roof warranty need?

Inland's metal roof guidelines list two coats of AldoCoat 400S for 10- and 15-year system warranties and three coats (the last one AldoCoat TE+) for 20 years. For polyurethane, they list two coats of AldoThane 386 for 10 and 15 years and three coats for 20 years. A hybrid schedule uses an AldoThane 384 base coat with an AldoSil 397 silicone top coat.

Is a roof coating covered by insurance after hail?

A coating isn't a hail repair, and coating over damage before it's documented can complicate a claim. Get the roof inspected first. In Texas it's generally 1 year from the date of loss to file, but check your policy.

Get a free roof inspection

We get on the roof, photograph what we find, and tell you plainly whether you need a repair or a replacement.

Get a free estimate

Tell us how to reach you. Blake or the team will call you back.

Or call (817) 733-9228